AKO D14918 Programming Key Instruction Manual

D149H181 Ed.08

AKO-D14918

Die AKO-D14918 programming key allows you to quickly and easily copy configured settings from one controller to another with the same functionality

Waarskuwings

-Using the equipment without following the manufacturer’s instructions may affect the device’s safety requirements.
-The unit must be used in a location protected from vibrations, water and corrosive gases, where the ambient temperature does not exceed that shown in the technical data.
-Connecting this key to unsupported devices (see table) can cause serious damage to both pieces of equipment.
-In equipment with active communication, log out of communications software or disconnect the cable before connecting the programming key. The communication controller’s address must be 1.

Beskrywing

1. LED COM
2. REKORD SLEUTEL
3. EXTERNAL POWER CONNECTOR
4. READ KEY
5. LED AAN
6. CONNECTOR CABLE

Verenigbaarheid

Refer to the instruction manual of your equipment on its compatibility with the AKO-D14918 programming key.

Connecting incompatible devices can permanently damage the key.

Bedrading

1. BELANGRIK: Pay attention to the orientation of the connector.
2. AKO-80018 
   (Opsioneel)
3. AKO-D14918

Kragtoevoer

-If the controller is in operation (on-site programming), the key does not require an external power supply (it is powered via the connecting cable).
-If the controller is NOT powered (workshop programming), the key requires a 12Vdc/500 mA external power supply (AKO-80018 or equivalent).

Operasie

BELANGRIK: After connecting the key to the equipment wait for 5 seconds before starting the reading or writing process.

RECORD key

Write the data contained in the key memory to the controller.
Keep the key pressed until the COM led starts flashing quickly.
When recording is complete the controller will reset.

READ key

It reads the data from the controller and stores them in the programming key.
Keep the key pressed until the COM led starts flashing quickly.
When recording is complete the controller will reset.

LED AAN

Steady or flashing: Indicates that the key is connected to the controller.

LED COM

Bestendig: Indicates an error in the transmission/reception of data
Flits vinnig: Indicates transmission/reception of data in progress. At the end of the transmission LED COM sal afskakel.
Stadig flikker: Indicates compatibility error- the data contained in the memory of the key is not compatible with the model of controller connected. Data can only be read from the controller to the key.

LET WEL: To restart after a transmission or compatibility error, turn off the power supply or disconnect the controller connector cable.

BELANGRIK: Nooit nie disconnect the programming key during data transmission.

Tegniese spesifikasies

Length of cable from programming key to controller . . . . . . . . . . . . . 300 mm
Voorsiening voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Vdc nominal
Supply current . . . . . . . . . . . . . . . . . . . . . . . . . . . . AKO-80018 / 500 mA máx.
Omgewingsspesifikasies:
Ambient working temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . 0ºC to 50ºC
Storage temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -30ºC to 70ºC

AKO ELECTROMECÁNICA, SA
Av. Roquetes, 30-38 | 08812 Sant Pere de Ribes | Barcelona | España

35D149181 REV.07 2025

Ons behou die reg voor om materiaal te verskaf wat effens kan verskil van dié wat in ons Tegniese Blaaie beskryf word.
Opgedateerde inligting is beskikbaar op ons webwebwerf.