Boardcon CM3576-stelsel op module
Spesifikasies
- Kenmerk: CM3576
- SVE: Quad-core Cortex-A72 en quad-core Cortex-A53
- RDD: 2 GB LPDDR4/x (tot 8 GB)
- eMMC: 32GB (tot 128GB opsie)
- FLITS UV: FLASH Krag EDP/MIPI DSI I2S MIPI CSI SATA HDMI uitset DP uitset RGB uitset EBC uitset Flex Bus
- Spesifikasies: 1-CH EDP, 1-CH MIPI DSI, 5-CH, 3-CH, 4-Laan of 4-CH, 2-Lane + 1-CH, 4-Lane CSI (tot 5 CSI-kameras), 2-CH , 1-CH (EDP-opsie), 1-CH, 1-CH, 24bit, 1-CH (opsie) opsie
- KAN: 2-CH
- USB: 1-CH Type-C en 1-CH USB Host3.0
- Ethernet: 1-ch 1GB PHY
- Bord afmeting: 57.5 x 44 mm
Produkgebruiksinstruksies
Opstel prosedures
- Koppel die nodige kragtoevoer volgens die pendefinisies.
- Verseker die stelsel voltage is binne die gespesifiseerde reeks (3.4V-5.5V).
- As jy randapparatuur soos kameras of skerms gebruik, koppel dit aan die toepaslike poorte op die bord.
Veiligheidsinligting
Gebruik altyd die gespesifiseerde kragtoevoer voltage reeks om te verhoed dat die bord of komponente beskadig word.
Probleemoplossing
As jy enige probleme ondervind tydens opstelling of werking, verwys na die probleemoplossingsafdeling van die handleiding vir leiding.
Gereelde vrae
- V: Wat moet ek doen as die bord nie krag kry nie aan?
A: Gaan die kragverbindings na en verseker die voltage is binne die gespesifiseerde reeks. As die probleem voortduur, verwys na die probleemoplossingsafdeling van die handleiding. - V: Kan ek die DDR-kapasiteit opgradeer?
A: Ja, die DDR-kapasiteit kan opgegradeer word tot 8GB volgens die genoemde spesifikasies.
CM3576 Verwysing Gebruikershandleiding
V1.20240628
Boardcon Embedded Design
www.armdesigner.com
Inleiding
Oor hierdie handleiding
Hierdie handleiding is bedoel om die gebruiker 'n oor te geeview van die raad en voordele, volledige kenmerkspesifikasies, en opstel van prosedures. Dit bevat ook belangrike veiligheidsinligting.
Terugvoer en opdatering van hierdie handleiding
Om ons kliënte te help om die meeste van ons produkte te maak, stel ons voortdurend bykomende en opgedateerde hulpbronne beskikbaar op die Boardcon webwerf (www.boardcon.com, www.armdesigner.com).
Dit sluit in handleidings, toepassingsnotas, programmering bvamples, en opgedateerde sagteware en hardeware. Loer gereeld in om te sien wat nuut is!
Wanneer ons werk aan hierdie opgedateerde hulpbronne prioritiseer, is terugvoer van kliënte die nommer een invloed. As jy vrae, opmerkings of bekommernisse oor jou produk of projek het, moet asseblief nie huiwer om ons te kontak by support@armdesigner.com.
Beperkte waarborg
Boardcon waarborg dat hierdie produk vry is van defekte in materiaal en vakmanskap vir 'n tydperk van een jaar vanaf datum van aankoop. Gedurende hierdie waarborgperiode sal Boardcon die defekte eenheid herstel of vervang in ooreenstemming met die volgende proses:
'n Afskrif van die oorspronklike faktuur moet ingesluit word wanneer die defekte eenheid aan Boardcon terugbesorg word. Hierdie beperkte waarborg dek nie skade wat voortspruit uit beligting of ander kragstuwings, misbruik, misbruik, abnormale werkingstoestande, of pogings om die funksie van die produk te verander of te wysig nie.
Hierdie waarborg is beperk tot die herstel of vervanging van die defekte eenheid. In geen geval sal Boardcon aanspreeklik of verantwoordelik wees vir enige verlies of skade nie, insluitend maar nie beperk tot enige verlore winste, toevallige of gevolglike skade, verlies van besigheid, of verwagte winste wat voortspruit uit die gebruik of onvermoë om hierdie produk te gebruik nie.
Herstelwerk wat na die verstryking van die waarborgtydperk gedoen word, is onderhewig aan 'n herstelheffing en die koste van terugsending. Kontak asseblief Boardcon om te reël vir enige hersteldiens en om herstelkoste-inligting te bekom.
CM3576 Inleiding
Opsomming
Die CM3576-stelsel-op-module is toegerus met Rockchip se RK356, dit het 'n vierkern Cortex-A72 en 'n vierkern Cortex-A53 verwerker, ingebedde Mali-G52 MC3 GPU en 6.0 TOPs NPU.
Dit is spesifiek ontwerp vir die hoëprestasie-toestelle soos 4K-video-toesigstelsel, AI Edge-berekeningstoestelle, intelligente interaktiewe toestelle, persoonlike rekenaars en robotte. Die hoë-prestasie multimedia verwerking en versnelling enjin oplossing kan kliënte help om nuwe tegnologie vinniger bekend te stel en verbeter die algehele oplossing doeltreffendheid.
Kenmerke
- Mikroverwerker
- Vierkern Cortex-A72 tot 2.2GHz
- Vierkern Cortex-A53 tot 1.8GHz
- 48KB I-kas 32KB D-kas en 1MB L2 vir A72 elke kern, 32KB I-kas 32KB D-kas en 512KB L2 vir A53 elke kern
- 6.0 TOPS Neurale Proses Eenheid
- Mali-G52 MC3 tot 1.0GHz
- Quad-core Cortex-M0 vir gebruikerstoepassing
- Geheue organisasie
- LPDDR4 of LPDDR4X RAM tot 16 GB
- EMMC tot 128GB
- Ondersteun UV tot 128GB
- Ondersteun FSPI Flash
- Begin ROM
- Ondersteun stelselkode aflaai deur USB OTG
- Veilige stelsel
- Ingeboude twee syfer-enjin
- Ondersteun sleutelleer om sleutel veilig te waarborg
- Ondersteun veilige bedryfstelsel en data deurmekaar
- Ondersteun OTP
- Video-dekodeerder/enkodeerder
- Ondersteun video-dekodering tot 8K@30fps
- Ondersteun H.265 enkodeer tot 8K@30fps of 4K@120fps
- H.264 HP-kodering tot 4K@60fps
- Prentgrootte tot 65520 x 65520
- Vertoon substelsel
- Video-uitset
- Ondersteun HDMI 2.1 TX met ARC, tot 4K@120fps of EDP TX-koppelvlak tot 4K@60Hz
- HDMI 2.1 ondersteun FRL-modus
- Ondersteun 4 bane MIPI DSI tot 4K@60Hz
- Ondersteun PD1.4a-koppelvlak tot 4K@60fps
- Ondersteun RGB 24bit-uitvoer
- Ondersteun E-ink skerm koppelvlak
- Video/Beeld-invoer
- Ondersteun 3-CH MIPI 4lane CSI-koppelvlakke of 4-CH MIPI 2lanes + 1-CH 4lanes CSI-koppelvlakke
- Ondersteun DVP 8-bis invoer
- Oudio
- Vyf I2S/PCM-koppelvlakke
- Ondersteun 8-ch TX/RX op I2S0/1
- Ondersteun Mic-skikking Tot 8ch PDM/TDM-koppelvlak
- Ondersteun 2-ch SPDIF uitset
- Ondersteun 2-ch SPDIF-invoer
- Ondersteun stemaktiwiteitopsporing
- USB / PCIE/SATA3
- Twee USB2.0 OTG-koppelvlakke
- Een Type-C of DP koppelvlakke
- Een USB3.0 Gasheer of PCIE2.1×1 of SATA3 koppelvlak.
- Een PCIE2.1×1 of SATA3 koppelvlak.
- SATA3 ondersteun vyf toestelle elke poort via PM skakelaar
- Ethernet
- Aan boord van RTL8211F/ YT8531
- I2C
- Tot 9-CH I2C
- Ondersteun standaardmodus en vinnige modus (tot 400kbit/s)
- I3C
- Tot 2-CH I3C
- Ondersteun HDR-modus (tot 30 Mbps)
- I2C versoenbaar
- SDIO / SDMMC
- Ondersteun SDIO 3.0-protokol
- Ondersteun SD3.0-kaart
- SPI
- Tot 5-ch SPI beheerders,
- Vol-dupleks sinchrone seriële koppelvlak
- UART
- Ondersteun tot 12 UARTs
- UART2 met 2 drade vir ontfouting
- Ingebedde twee 64-grepe EIEU
- KAN
- Ondersteun tot twee CAN-beheerders
- Ondersteun CAN FD-protokol
- ADC
- Tot twee ADC-kanale
- 12-bis resolusie tot 1MS/ssampling koers
- Voltage insetreeks tussen 0V tot 1.8V
- PWM
- Tot 4 PWM's met onderbrekingsgebaseerde werking
- Ondersteun 32bit tyd/toonbankfasiliteit
- Krag eenheid
- PMU RK806 aan boord
- 3.4 ~ 5.5V hoofkraginvoer
- 1.8V en 3.3V maksimum 500mA uitset
- Baie lae RTC verbruik stroom, minder 5uA by 3V knoppie Sel.
CM3576 Blokdiagram
RK3576 Blokdiagram
Ontwikkelingsbord (EM3576) Blokdiagram
CM3576 spesifikasies
| Kenmerk | Spesifikasies |
| SVE | Quad-core Cortex-A72 en quad-core Cortex-A53 |
| DDR | 2 GB LPDDR4/x (tot 8 GB) |
| eMMC-FLITS | 32 GB (tot 128 GB) |
| UV-FLITS | opsie |
| Krag | DC 3.4~5.5V |
| EDP/MIPI DSI | 1-CH EDP, 1-CH MIPI DSI |
| I2S | 5-CH |
| MIPI CSI | 3-CH 4-Lane of 4-CH 2-Lane + 1-CH 4-Lan CSI (tot 5 CSI-kameras) |
| SATA | 2-CH |
| HDMI-uitset | 1-CH (EDP-opsie) |
| DP-uitset | 1-CH |
| RGB-uitset | 1-CH 24bit |
| EBC uitset | 1-CH (opsie) |
| Flex Bus | opsie |
| Kenmerk | Spesifikasies |
| KAN | 2-CH |
| USB | 1-CH Type-C en 1-CH USB Host3.0 |
| Ethernet | 1-ch 1GB PHY |
| SDMMC | 2-CH |
| SPDIF TX | 2-CH |
| SPDIF RX | 2-CH |
| I2C | 9-CH |
| I3C | 2-CH |
| SPI | 5-CH |
| KAN | 2-CH |
| UART | 11-CH, 1-CH(DEBUG) |
| PWM | 4-CH |
| ADC IN | 2-CH |
| Bord afmeting | 57.5 x 44 mm |
CM3576 PCB Dimensie
CM3576 Pen Definisie
| Speld vas | Sein | Beskrywing of funksies | GPIO reeks | IO Voltage |
| 1 | VCC_SYS | Stelselkraginvoer | 3.4V-5.5V | |
| 2 | VCC_SYS | Stelselkraginvoer | 3.4V-5.5V | |
| 3 | VCC_SYS | Stelselkraginvoer | 3.4V-5.5V | |
| 4 | PWRON_L | Kragsleutel-invoer | 3.4V-5.5V | |
| 5 | VCC_3V3_S3 | 3.3V GPIO kraguitset | Maks 500mA | 3.3 V |
| Speld vas | Sein | Beskrywing of funksies | GPIO reeks | IO Voltage |
| 6 | UART0_TX_M0 | Vir ontfouting verstek | GPIO0_D4_u | 3.3 V |
| 7 | UART0_RX_M0 | Vir ontfouting verstek | GPIO0_D5_u | 3.3 V |
| 8 | GND | Grond | 0V | |
| 9 | RESET_L | GPIO0_A1_z gekoppel (PU) | 1.8 V | |
| 10 | SDMMC0_DET_L_1V8 | (PU100K) | GPIO0_A7_u | 1.8 V |
|
11 |
WIFI_WAKE_HOST_H
_1V8 |
I2C0_SCL_M0 |
GPIO0_B0_z |
1.8 V |
|
12 |
BT_WAKE_HOST_H_1
V8 |
I2C0_SDA_M0 |
GPIO0_B1_z |
1.8 V |
|
13 |
HOST_WAKE_BT_H_1 V8 |
SPDIF_TX1_M2/SPI2_CLK_ M1/PDM0_CLK1_M2/CLK1_
32K_OUT/SATA_MPSWIT |
GPIO1_D5_d |
1.8 V |
|
14 |
SAI2_SCLK_M0_1V8 |
I3C0_SDA_PU_M1/UART10
_RX_M1 |
GPIO1_D1_d |
1.8 V |
| 15 | SAI2_SDO_M0_1V8 | UART10_TX_M1 | GPIO1_D0_d | 1.8 V |
|
16 |
SAI2_SDI_M0_1V8 |
I3C0_SDA_M1/PWM1_CH4_
M1 |
GPIO1_D3_d |
1.8 V |
|
17 |
SAI2_LRCK_M0_1V8 |
I3C0_SCL_M1/PWM1_CH3_
M1 |
GPIO1_D2_d |
1.8 V |
|
18 |
WIFI_REG_ON_H_1V8 |
I2C8_SCL_M1/UART2_TX_ M0/PDM0_SDI0_M2/SATA_
CPPOD |
GPIO1_C6_d |
1.8 V |
|
19 |
BT_REG_ON_H_1V8 |
I2C8_SDA_M1/UART2_RX_
M0/PDM0_SDI1_M2/SATA_ CPDET |
GPIO1_C7_d |
1.8 V |
|
20 |
UART4_CTSN_M1_1V
8 |
SDMMC1_DET_M0/I2C6_S
DA_M1/SPI2_CSN0_M1 |
GPIO1_C3_u |
1.8 V |
|
21 |
UART4_RTSN_M1_1V 8 |
SDMMC1_PWEN_M0/I2C6_ SCL_M1/SPI2_CSN1_M1/P
WM1_CH2_M1 |
GPIO1_C2_u |
1.8 V |
|
22 |
UART4_TX_M1_1V8 |
SPI2_MOSI_M1/UART2_RT
S_M0/PCIE0_BUTTONRST |
GPIO1_C4_d |
1.8 V |
| 23 | UART4_RX_M1_1V8 | SPI2_MISO_M1/UART2_CT
S_M0/PCIE1_BUTTONRST |
GPIO1_C5_d | 1.8 V |
| 24 | SDMMC1_D1_M0_1V8 | I2C9_SCL_M1/SPI1_MOSI_
M0/PCIE1_WAKE_M1/SAI3_ LRCK_M1/PWM1_CH1_M1 |
GPIO1_B5_d | 1.8 V |
| 25 | SDMMC1_D0_M0_1V8 | I2C9_SDA_M1/SPI1_CLK_M 0/PCIE1_CLKREQ_M1/SAI3
_SCLK_M1/PWM1_CH0_M1 |
GPIO1_B4_d | 1.8 V |
| Speld vas | Sein | Beskrywing of funksies | GPIO reeks | IO Voltage |
|
26 |
SDMMC1_D2_M0_1V8 |
UART3_CTS_M2/SPI1_MIS O_M0/PCIE0_CLKREQ_M1/
SAI3_SDO_M1 |
GPIO1_B6_d |
1.8 V |
|
27 |
SDMMC1_D3_M0_1V8 |
UART3_RTS_M2/SPI1_CSN 0_M0/PCIE0_WAKE_M1/SAI
3_SDI_M1 |
GPIO1_B7_d |
1.8 V |
|
28 |
SDMMC1_CMD_M0_1 V8 |
UART3_TX_M2/SPI1_CSN1
_M0/PDM0_SDI2_M2/PWM0 _CH0_M1 |
GPIO1_C0_d |
1.8 V |
|
29 |
SDMMC1_CLK_M0_1V
8 |
UART3_RX_M2/PDM0_CLK
0_M2/SAI3_MCLK_M1 |
GPIO1_C1_d |
1.8 V |
| 30 | GND | Grond | 0V | |
|
31 |
RECOVERY_SARADC
_VIN1 |
HERSTEL
MODUS/ADC_IN1(PU10K) |
1.8 V |
|
| 32 | SARADC_VIN2 | ADC_IN2 | 1.8 V | |
| 33 | GND | Grond | 0V | |
|
34 |
SDMMC0_CLK |
I3C1_SDA_PU_M1/I2C5_SC
L_M0/UART5_TX_M2/SPI0_ CLK_M1/SAI3_SCLK_M3 |
GPIO2_A5_d/ FSPI1_CLK_M0 |
3.3 V |
|
35 |
SDMMC0_D1 |
DSM_ALN_M0/I2C8_SDA_M 0/UART0_TX_M1/UART7_T X_M2/SPI0_MISO_M1/CAN0
_TX_M0/SAI3_MCLK_M3 |
GPIO2_A1_d/ PWM2_CH3_M0/ FSPI1_D1_M0 |
3.3 V |
|
36 |
SDMMC0_D0 |
DSM_ALP_M0/I2C8_SCL_M 0/UART0_RX_M1/UART7_R X_M2/SPI0_MOSI_M1/CAN0
_RX_M0 |
GPIO2_A0_d/ PWM2_CH2_M0/ FSPI1_D0_M0 |
3.3 V |
|
37 |
SDMMC0_CMD |
I2C5_SDA_M0/UART5_RX_ M2/SPI0_CSN0_M1/SAI3_S
DO_M3 |
GPIO2_A4_d/ PWM2_CH4_M0/
FSPI1_CSN0_M0 |
3.3 V |
|
38 |
SDMMC0_D3 |
I3C1_SDA_M1/DSM_ARN_ M0/UART5_CTSN_M2/SAI3
_SDI_M3/CAN1_TX_M0 |
GPIO2_A3_d/
FSPI1_D3_M0/ JTAG_TMS_M0 |
3.3 V |
|
39 |
SDMMC0_D2 |
I3C1_SCL_M1/DSM_ARP_M
0/UART5_RTSN_M2/SAI3_L RCK_M3/CAN1_RX_M0 |
GPIO2_A2_d/
FSPI1_D2_M0/ JTAG_TCK_M0 |
3.3 V |
|
40 |
LCDC_DEN/EBC_SDL E/DSMC_DATA0 |
I2C3_SCL_M2/UART5_RX_ M0/SPI3_CLK_M1/SAI1_SDI
1_M1/FLEXBUS1_D1 |
GPIO3_D4_d |
3.3 V |
|
41 |
LCDC_VSYNC/EBC_S DCLK/DSMC_CLKN |
UART5_CTS_M0/SPI3_MOS
I_M1/SAI1_SDI3_M1/FLEXB US1_CLK/PWM2_CH6_M3 |
GPIO3_D6_d |
3.3 V |
| Speld vas | Sein | Beskrywing of funksies | GPIO reeks | IO Voltage |
|
42 |
LCDC_HSYNC/EBC_G DCLK/DSMC_CLKP |
I2C3_SDA_M2/UART5_TX_ M0/SPI3_MISO_M1/SAI1_S
DI2_M1/FLEXBUS1_D0 |
GPIO3_D5_d |
3.3 V |
|
43 |
LCDC_CLK/EBC_SDO E/DSMC_RESETN |
UART5_RTS_M0/SPI3_CSN 1_M1/SAI4_SCLK_M1/FLEX BUS1_D12_M0/FLEXBUS0_ D15_M0/FLEXBUS1_CSn_M
1/CAM_CLK0_OUT_M0 |
GPIO3_D7_d/ PWM2_CH7_M3 |
3.3 V |
|
44 |
DSMC_INT0/GPIO4_A 0_d |
I2C7_SCL_M2/UART3_TX_ M0/SPI1_CSN1_M2/SAI4_L RCK_M1/FLEXBUS1_D14_ M0/FLEXBUS0_D13_M0/FL EXBUS1_CSn_M3/CAM_CL
K1_OUT_M0 |
GPIO4_A0_d/ MIPI_TE_M2/ SPDIF_RX0_M1 |
3.3 V |
|
45 |
DSMC_INT2/GPIO4_A 1_d |
I2C7_SDA_M2/UART3_RX_ M0/SAI4_SDO_M1/FLEXBU S1_D13_M0/FLEXBUS0_D1 4_M0/FLEXBUS0_CSn_M1/
CAM_CLK2_OUT_M0 |
GPIO4_A1_d/ VO_POST_EMPTY/ SPDIF_TX0_M1 |
3.3 V |
|
46 |
PHY1_LED1/CFG_LD
O0 |
Spoed LED (PD4.7K) |
3.3 V |
|
|
47 |
PHY1_LED2/CFG_LD
O1 |
Skakel LED (PD4.7K) |
3.3 V |
|
| 48 | PHY1_MDI0+ | 0.5 V | ||
| 49 | PHY1_MDI0- | 0.5 V | ||
| 50 | PHY1_MDI1+ | 0.5 V | ||
| 51 | PHY1_MDI1- | 0.5 V | ||
| 52 | PHY1_MDI2+ | 0.5 V | ||
| 53 | PHY1_MDI2- | 0.5 V | ||
| 54 | PHY1_MDI3+ | 0.5 V | ||
| 55 | PHY1_MDI3- | 0.5 V | ||
| 56 | 32KOUT_RTC_1V8 | RTC_CLK 32.768KHz uitset | GPIO0_A2_d | 1.8 V |
| 57 | VCC_RTC | RTC-kraginvoer | 1.8~3.3V | |
|
58 |
LCDC_D0/EBC_SDDO 0/DSMC_CSN0 |
I3C1_SCL_M2/UART2_CTS
_M2/SAI2_SDO_M2/FLEXB US1_D2 |
GPIO3_D3_d/ PWM2_CH5_M3 |
3.3 V |
|
59 |
LCDC_D1/EBC_SDDO 1/DSMC_CSN3 |
I3C1_SDA_M2/UART2_RTS
_M2/SPI4_CSN1_M1/SAI2_ SDI_M2/FLEXBUS0_D12/FL EXBUS0_CS_M3/FLEXBUS 1_D15_M0 |
GPIO3_D2_d/ PWM2_CH4_M3 |
3.3 V |
| Speld vas | Sein | Beskrywing of funksies | GPIO reeks | IO Voltage |
|
60 |
LCDC_D2/EBC_SDDO 2/DSMC_CSN2 |
I3C1_SDA_PU_M2/SPI4_CL K_M1/SAI2_MCLK_M2/FLEX BUS0_D11/FLEXBUS1_CS_
M2 |
GPIO3_D1_d |
3.3 V |
|
61 |
LCDC_D3/EBC_SDDO 3/DSMC_DATA1 |
UART8_CTS_M0/SPI1_CSN 0_M2/SAI1_MCLK_M1/FLEX
BUS1_D3 |
GPIO3_D0_d/ PWM2_CH3_M3 |
3.3 V |
|
62 |
LCDC_D4/EBC_SDDO 4/DSMC_DATA2 |
UART8_RTS_M0/SPI1_CLK
_M2/SAI1_SCLK_M1/FLEXB US1_D4 |
GPIO3_C7_d |
3.3 V |
|
63 |
LCDC_D5/EBC_SDDO 5/DSMC_DATA3 |
UART8_TX_M0/SPI1_MOSI
_M2/SAI1_LRCK_M1/FLEXB US1_D5 |
GPIO3_C6_d |
3.3 V |
|
64 |
LCDC_D6/EBC_SDDO 6/DSMC_DATA4 |
UART8_RX_M0/SPI1_MISO
_M2/SAI1_SDO0_M1/FLEXB US1_D6 |
GPIO3_C5_d/ PWM2_CH2_M3 |
3.3 V |
|
65 |
LCDC_D7/EBC_SDDO 7/DSMC_DATA5 |
I2C5_SCL_M3/UART11_TX_ M0/SPI2_CSN0_M2/SAI1_S DO0_M1/FLEXBUS1_D7/CA
N0_TX_M3 |
GPIO3_C4_d |
3.3 V |
|
66 |
LCDC_D8/EBC_SDDO 8/DSMC_INT3 |
I2C9_SDA_M3/UART11_CT S_M0/SPI4_MOSI_M1/SAI2_ LRCK_M2/FLEXBUS0_D10/
FLEXBUS0_CSN_M2 |
GPIO3_C3_d/ PWM2_CH1_M3 |
3.3 V |
|
67 |
LCDC_D9/EBC_SDDO 9/DSMC_INT1 |
I2C9_SCL_M3/UART11_RTS
_M0/SPI4_MISO_M1/SAI2_S CLK_M2/FLEXBUS0_D9 |
GPIO3_C2_d/ PWM2_CH0_M3 |
3.3 V |
|
68 |
LCDC_D10/EBC_SDD O10/DSMC_DATA6 |
I2C5_SCL_M3/UART11_RX_ M0/SPI2_MISO_M2/SAI1_S DO2_M1/FLEXBUS1_D8/CA
N0_RX_M3 |
GPIO3_C1_d |
3.3 V |
|
69 |
LCDC_D11/EBC_SDD O11/DSMC_DATA7 |
I2C4_SCL_M3/UART2_TX_ M2/UART3_RTS_M1/SAI1_S
DO3_M1/FLEXBUS1_D9 |
GPIO3_C0_d |
3.3 V |
|
70 |
LCDC_D12/EBC_SDD O12/DSMC_DQS0 |
I2C4_SDA_M3/UART2_RX_ M2/UART3_CTS_M1/SAI1_S DO0_M1/FLEXBUS1_D10/F
LEXBUS1_CSN_M0 |
GPIO3_B7_d |
3.3 V |
|
71 |
LCDC_D13/EBC_SDD
O13/DSMC_DQS1 |
SPI3_CSN0_M1/ETH0_TXC
LK_M0/FLEXBUS0_CLK |
GPIO3_B6_d/
PWM0_CH1_M3 |
3.3 V |
|
72 |
LCDC_D14/EBC_SDD O14/DSMC_DATA8 |
UART9_CTS_M1/ETH0_TX D0_M0/SPDIF_TX1_M0/FLE
XBUS0_D0 |
GPIO3_B5_d/ PWM1_CH5_M3 |
3.3 V |
| Speld vas | Sein | Beskrywing of funksies | GPIO reeks | IO Voltage |
|
73 |
LCDC_D15/EBC_SDD O15/DSMC_DATA9 |
UART9_RTS_M1/ETH0_TX D1_M0/SPDIF_RX1_M0/FLE
XBUS0_D1 |
GPIO3_B4_d/ PWM1_CH4_M3 |
3.3 V |
|
74 |
LCDC_D16/EBC_SDC E0/DSMC_DATA10 |
I2C8_SCL_M3/UART9_TX_ M1/ETH0_TXCTL_M0/PDM1
_SDI0_M2/FLEXBUS0_D2 |
GPIO3_B3_d |
3.3 V |
|
75 |
LCDC_D17/EBC_SDC E1/DSMC_DATA11 |
I2C8_SDA_M3/UART9_RX_ M1/ETH0_RXD0_M0/PDM1_
SDI1_M2/FLEXBUS0_D3 |
GPIO3_B2_d |
3.3 V |
|
76 |
LCDC_D18/EBC_SDC E2/DSMC_DATA12 |
UART10_TX_M0/SPI4_CSN 0_M1/ETH0_RXD1_M0/PDM
1_CLK0_M2/FLEXBUS0_D4 |
GPIO3_B1_d/ PWM1_CH3_M3 |
3.3 V |
|
77 |
LCDC_D19/EBC_SDC E3/DSMC_CSN1 |
UART10_RX_M0/SPI2_MOS I_M2/ETH0_MCLK_M0/SAI4
_MCLK_M1/FLEXBUS0_D8 |
GPIO3_B0_d/ PWM0_CH0_M3 |
3.3 V |
|
78 |
LCDC_D20/EBC_VCO M/DSMC_DATA13 |
UART10_RTS_M0/UART1_T X_M2/ETH0_RXCTL_M0/PD
M1_CLK1_M2/FlexBUS0_D5 |
GPIO3_A7_d |
3.3 V |
|
79 |
LCDC_D21/EBC_GDO E/DSMC_DATA14 |
UART10_CTS_M0/UART1_ RX_M2/ETH0_MDC_M0/PD
M1_SDI2_M2/FlexBUS0_D6 |
GPIO3_A6_d/ PWM1_CH2_M3 |
3.3 V |
|
80 |
LCDC_D22/EBC_GDS P/DSMC_DATA15 |
SPI2_CSn1_M2/UART1_RT S_M2/ETH0_MDIO_M0/PDM
1_SDI3_M2/FlexBUS0_D7 |
GPIO3_A5_d/ PWM1_CH1_M3 |
3.3 V |
|
81 |
LCDC_D23/EBC_SDS HR/DSMC_RDYN |
SPI2_CLK_M2/UART1_CTS
_M2/ETH0_CLKOUT_25M_ M0/SAI4_SDI_M1/FlexBUS1 _D11/FlexBUS0_CSn_M0 |
GPIO3_A4_d/ PWM1_CH0_M3 |
3.3 V |
|
82 |
TYPEC_DPTX_AUX_P
UPDCTL1 |
AUPLL_CLKIN_M2/SAI1/4_
MCLK_M0 |
GPIO4_A2_d
/PWM2_CH5_M0 |
3.3 V |
|
83 |
PCIE1_CLKREQn_M2 |
I2C2_SDA_M2/UART5_CTS
_M1/SPI4_CS1_M2/SAI1_LR CK_M0/FlexBUS1_D12_M1 |
GPIO4_A5_d |
3.3 V |
|
84 |
PCIE1_PWREN_H |
I2C2_SCL_M2/UART5_RTS
_M1/SPI3_CS0_M2/SAI1_S CLK_M0/FlexBUS1_CS_M4 |
GPIO4_A3_d/ PWM2_CH4_M1 |
3.3 V |
|
85 |
HDMI_TX_ON_H |
I2C4_SDA_M1/UART6_RX_ M0/SPI3_MISO_M2/SAI4_L RCK_M0/PDM1_CLK0_M1/F
lexBUS1_D14_M1/CAN0_RX _M2 |
GPIO4_A6_d |
3.3 V |
| Speld vas | Sein | Beskrywing of funksies | GPIO reeks | IO Voltage |
|
86 |
TYPEC_DPTX_AUX_P UPDCTL2 |
I2C4_SCL_M1/UART6_TX_ M0/SPI3_MOSI_M2/SAI4_S CLK_M0/PDM1_SDI3_M1/Fl exBUS1_D13_M1/CAN0_TX
_M2 |
GPIO4_A4_d |
3.3 V |
|
87 |
HP_CTL_H |
SPI3_CLK_M2/SAI4_SDI_M
0/SAI1_SDO0_M0 |
GPIO4_A7_d/
PWM2_CH6_M0 |
3.3 V |
|
88 |
I2C3_SCL_M0_Sensor |
PCIE0_CLKREQ_M2/IUART
2_TX_M1/SPDIF_TX0_M0/Fl exBUS0_D15_M1/CAN1_TX _M2 |
GPIO4_B5_d (PU2.2K) |
3.3 V |
|
89 |
I2C3_SDA_M0_Sensor |
PCIE0_WAKE_M2/IUART2_
RX_M1/SPDIF_RX0_M0/Fle xBUS0_CSN_M4/CAN1_RX _M2 |
GPIO4_B4_d (PU2.2K) |
3.3 V |
|
90 |
SPK_CTL_H |
SPI3_CS1_M2/SPI4_CS0_M 2/PDM1_SDI0_M1/SAI1_SDI
0_M0/SAI4_SDO_M0 |
GPIO4_B3_d/ PWM2_CH7_M0 |
3.3 V |
|
91 |
PCIE1_PERSTn |
SPI4_MISO_M2/PDM1_SDI1
_M1/SAI1_SDI1_M0/SAI1_S DO3_M0/FlexBUS1_D15_M1 |
GPIO4_B2_d/ MIPI_TE_M0 |
3.3 V |
|
92 |
IRC_BIN |
UART2_CTS_M1/UART6_C TS_M0/UART5_RX_M1/SPI4
_MOSI_M2/PDM1_SDI2_M1/ SAI1_SDI2_M0/SAI1_SDO2 _M0/FlexBUS1_D14_M1 |
GPIO4_B1_d |
3.3 V |
|
93 |
IRC_AIN |
UART2_RTS_M1/UART6_R TS_M0/UART5_TX_M1/SPI4
_CLK_M2/PDM1_CLK1_M1/ SAI1_SDI3_M0/SAI1_SDO1 _M0/FlexBUS1_D13_M1 |
GPIO4_B1_d |
3.3 V |
|
94 |
PCIE0_CLKREQn_M3 |
I2C6_SCL_M3/SPI4_MISO_ M0/SAI4_SDI_M2/VP1_SYN
C_OUT/CAN1_TX_M1 |
GPIO4_C6_d/ PWM2_CH2_M1/
SATA0_ACTLED_M1 |
3.3 V |
|
95 |
PCIE0_PERSTn |
I2C6_SDA_M3/SPI4_CLK_M 0/SAI4_SCLK_M2/VP2_SYN
C_OUT/CAN1_RX_M1 |
GPIO4_C7_d/ PWM2_CH3_M1 |
3.3 V |
|
96 |
PWM2_CH5_M1_FAN |
I2C3_SDA_M3/UART6_RX_ M3/SPI4_MOSI_M0/SAI4_S DO_M2/VP0_SYNC_OUT/IS
P_FLASH_TRIGOUT_M1 |
GPIO4_C5_d/ PWM2_CH5_M1/ SATA1_ACTLED_M1
PCIE0_WAKE_M3 |
3.3 V |
| Speld vas | Sein | Beskrywing of funksies | GPIO reeks | IO Voltage |
|
97 |
HDMI_TX_HPDIN_M0 |
I2C7_SDA_M3/UART11_RX
_M2/EDP_HPD_M0/PCIE1_ CLKREQ_M3/DSM_ALN_M1 |
GPIO4_C1_d/ PWM0_CH1_M1 |
3.3 V |
|
98 |
HDMI_TX_SDA |
I2C2_SDA_M3/UART9_RX_
M2/CAN0_RX_M1/DSM_AR N_M1 |
GPIO4_C3_d/ PWM2_CH1_M1 |
3.3 V |
|
99 |
HDMI_TX_SCL |
I2C2_SCL_M3/UART9_TX_ M2/CAN0_TX_M1/DSM_AR
P_M1 |
GPIO4_C2_d/ PWM2_CH0_M1 |
3.3 V |
|
100 |
DP_HPDIN_M0 |
I2C3_SCL_M3/UART6_TX_ M3/SPI4_CSn0_M0/SAI4_LR CK_M2/ISP_PRLIGHT_TRIG
_M1 |
GPIO4_C4_d/ PWM2_CH6_M1 |
3.3 V |
|
101 |
HDMI_TX_CEC_M0 |
I2C7_SCL_M3/UART11_TX_ M2/SPI4_CSn1_M0/SAI_MC
LK_M2/DSM_ALP_M1 |
GPIO4_C0_d/ PWM1_CH5_M1/
PCIE1_WAKE_M3 |
3.3 V |
| 102 | GND | Grond | 0V | |
|
103 |
MIPI_DPHY_CSI0_PW REN_H_1V8 |
UART3_RTS_M0/SPI3_CSn 0_M0/SAI3_SDI_M2/ETH0_
RXD1_M1/CAN_RX_M3 |
GPIO3_A3_d/ VI_CIF_CLKI/
SPDIF_TX1_M1 |
1.8 V |
|
104 |
SAI0_SDI0_M0_1V8 |
UART1_TX_M1/PDM0_SDI3
_M3/ETH0_TXD1_M1 |
GPIO2_B0_d/
VI_CIF_D13 |
1.8 V |
|
105 |
SAI0_SDI1_M0_1V8 |
UART1_RX_M1/PDM0_SDI2
_M3/ETH0_TXD0_M1 |
GPIO2_B1_d/
VI_CIF_D12 |
1.8 V |
|
106 |
SAI0_SDI2_M0_1V8 |
UART1_CTS_M1/SPI4_CSn 0_M3/PDM0_SDI1_M3/PCIE
0_CLKREQ_M0 |
GPIO2_B2_d/ VI_CIF_D11 |
1.8 V |
|
107 |
SAI0_SDI3_M0_1V8 |
UART7_CTS_M1/SPI4_MOS I_M3/PDM0_SDI0_M3/SATA
0_ACTLED_M0 |
GPIO2_B4_d/ VI_CIF_D9 |
1.8 V |
|
108 |
SAI0_SCLK_M0_1V8 |
I2C8_SCL_M2/UART8_CTS
_M1/UART7_RX_M0 |
GPIO2_B6_d |
1.8 V |
|
109 |
SAI0_LRCK_M0_1V8 |
I2C8_SDA_M2/UART8_RTS
_M1/UART7_TX_M0 |
GPIO2_B7_d |
1.8 V |
|
110 |
SAI0_MCLK_M0_1V8 |
UART7_RTS_M0/SPI4_MIS O_M3/PDM0_CLK0_M3/SAT
A1_ACTLED_M0 |
GPIO2_B5_d/ VI_CIF_D8 |
1.8 V |
|
111 |
SAI0_SDO0_M0_1V8 |
I2C4_SCL_M2/UART8_TX_
M1/SPI4_CSn1_M3/ETH0_R XD0_M1 |
GPIO2_A6_d/ VI_CIF_D15 |
1.8 V |
|
112 |
SAI0_SDO1_M0_1V8 |
I2C4_SDA_M2/UART8_RX_
M1/ETH0_TXCTL_M1 |
GPIO2_A7_d/
VI_CIF_D14 |
1.8 V |
| Speld vas | Sein | Beskrywing of funksies | GPIO reeks | IO Voltage |
|
113 |
SAI0_SDO2_M0_1V8 |
UART1_RTS_M1/SPI4_CLK
_M3/PDM0_CLK1_M3/PCIE 1_CLKREQ_M0 |
GPIO2_B3_d/ VI_CIF_D10 |
1.8 V |
|
114 |
SPDIF_RX1_M1_1V8 |
UART3_RTS_M0/SPI3_MIS O_M0/SAI3_SDO_M2/ETH0
_RXCTL_M1/CAN_TX_M3 |
GPIO3_A2_d/
VI_CIF_CLKO/ MIPI_TE_M1 |
1.8 V |
|
115 |
I2C7_SDA_M1_1V8 |
UART3_RX_M0/SPI3_MOSI
_M0/SAI3_LRCK_M2/ETH0_ MDC_M1(PU2.2K) |
GPIO3_A1_d/ VI_CIF_VSYNC |
1.8 V |
|
116 |
I2C7_SCL_M1_1V8 |
UART3_TX_M0/SPI3_CLK_
M0/SAI3_SCLK_M2/ETH0_ MDIO_M1(PU2.2K) |
GPIO3_A0_d/ VI_CIF_HREF |
1.8 V |
| 117 | GND | Grond | 0V | |
| 118 | DP_TX_AUXP | 0.5 V | ||
| 119 | DP_TX_AUXN | 0.5 V | ||
| 120 | USB2_OTG1_DP | 0.5 V | ||
| 121 | USB2_OTG1_DM | 0.5 V | ||
| 122 | USB2_OTG0_DP | 0.5 V | ||
| 123 | USB2_OTG0_DM | 0.5 V | ||
|
124 |
USB3_OTG0_SSRX1N
/DP_TX_D0N |
0.5 V |
||
|
125 |
USB3_OTG0_SSRX1P
/DP_TX_D0P |
0.5 V |
||
|
126 |
USB3_OTG0_SSTX1P/
DP_TX_D1P |
0.5 V |
||
|
127 |
USB3_OTG0_SSTX1N/
DP_TX_D1N |
0.5 V |
||
|
128 |
USB3_OTG0_SSRX2N
/DP_TX_D2N |
0.5 V |
||
|
129 |
USB3_OTG0_SSRX2P
/DP_TX_D2P |
0.5 V |
||
|
130 |
USB3_OTG0_SSTX2P/
DP_TX_D3P |
0.5 V |
||
|
131 |
USB3_OTG0_SSTX2N/
DP_TX_D3N |
0.5 V |
||
| 132 | GND | Grond | 0V | |
|
133 |
MIPI_DPHY_DSI_TX_
D0N |
MIPI_CPHY_DSI_TX_TRIO0
A |
0.5 V |
|
|
134 |
MIPI_DPHY_DSI_TX_
D0P |
MIPI_CPHY_DSI_TX_TRIO0
B |
0.5 V |
|
|
135 |
MIPI_DPHY_DSI_TX_
D1N |
MIPI_CPHY_DSI_TX_TRIO0
C |
0.5 V |
| Speld vas | Sein | Beskrywing of funksies | GPIO reeks | IO Voltage |
|
136 |
MIPI_DPHY_DSI_TX_
D1P |
MIPI_CPHY_DSI_TX_TRIO1
A |
0.5 V |
|
|
137 |
MIPI_DPHY_DSI_TX_
CLKN |
MIPI_CPHY_DSI_TX_TRIO1
B |
0.5 V |
|
|
138 |
MIPI_DPHY_DSI_TX_
CLKP |
MIPI_CPHY_DSI_TX_TRIO1
C |
0.5 V |
|
|
139 |
MIPI_DPHY_DSI_TX_
D2N |
MIPI_CPHY_DSI_TX_TRIO2
A |
0.5 V |
|
|
140 |
MIPI_DPHY_DSI_TX_
D2P |
MIPI_CPHY_DSI_TX_TRIO2
B |
0.5 V |
|
|
141 |
MIPI_DPHY_DSI_TX_
D3N |
MIPI_CPHY_DSI_TX_TRIO2
C |
0.5 V |
|
|
142 |
MIPI_DPHY_DSI_TX_
D3P |
0.5 V |
||
|
143 |
MIPI_DPHY_CSI0_RX
_D0P |
MIPI_CPHY_CSI_TX_TRIO0
B |
0.5 V |
|
|
144 |
MIPI_DPHY_CSI0_RX
_D0N |
MIPI_CPHY_CSI_TX_TRIO0
A |
0.5 V |
|
|
145 |
MIPI_DPHY_CSI0_RX
_D1P |
MIPI_CPHY_CSI_TX_TRIO1
A |
0.5 V |
|
|
146 |
MIPI_DPHY_CSI0_RX
_D1N |
MIPI_CPHY_CSI_TX_TRIO0
C |
0.5 V |
|
|
147 |
MIPI_DPHY_CSI0_RX
_CLKP |
MIPI_CPHY_CSI_TX_TRIO1
C |
0.5 V |
|
|
148 |
MIPI_DPHY_CSI0_RX
_CLKN |
MIPI_CPHY_CSI_TX_TRIO1
B |
0.5 V |
|
|
149 |
MIPI_DPHY_CSI0_RX
_D2P |
MIPI_CPHY_CSI_TX_TRIO2
B |
0.5 V |
|
|
150 |
MIPI_DPHY_CSI0_RX
_D2N |
MIPI_CPHY_CSI_TX_TRIO2
A |
0.5 V |
|
|
151 |
MIPI_DPHY_CSI0_RX
_D3P |
0.5 V |
||
|
152 |
MIPI_DPHY_CSI0_RX
_D3N |
MIPI_CPHY_CSI_TX_TRIO2
C |
0.5 V |
|
| 153 | GND | Grond | 0V | |
| 154 | HDMI_TX_D3N | EDP_TX3N | 0.5 V | |
| 155 | HDMI_TX_D3P | EDP_TX3P | 0.5 V | |
| 156 | HDMI_TX_D0P | EDP_TX0P | 0.5 V | |
| 157 | HDMI_TX_D0N | EDP_TX0N | 0.5 V | |
| 158 | HDMI_TX_D1P | EDP_TX1P | 0.5 V | |
| 159 | HDMI_TX_D1N | EDP_TX1N | 0.5 V | |
| 160 | HDMI_TX_D2P | EDP_TX2P | 0.5 V |
| Speld vas | Sein | Beskrywing of funksies | GPIO reeks | IO Voltage |
| 161 | HDMI_TX_D2N | EDP_TX2N | 0.5 V | |
| 162 | HDMI_TX_SBDN | EDP_AUXN | 0.5 V | |
| 163 | HDMI_TX_SBDP | EDP_AUXP | 0.5 V | |
| 164 | GND | Grond | 0V | |
|
165 |
MIPI_DPHY_CSI2_RX
_CLKP |
0.5 V |
||
|
166 |
MIPI_DPHY_CSI2_RX
_CLKN |
0.5 V |
||
|
167 |
MIPI_DPHY_CSI1_RX
_CLKN |
0.5 V |
||
|
168 |
MIPI_DPHY_CSI1_RX
_CLKP |
0.5 V |
||
|
169 |
MIPI_DPHY_CSI1_RX
_D3N |
MIPI_DPHY_CSI2_RX_D1N |
0.5 V |
|
|
170 |
MIPI_DPHY_CSI1_RX
_D3P |
MIPI_DPHY_CSI2_RX_D1P |
0.5 V |
|
|
171 |
MIPI_DPHY_CSI1_RX
_D2N |
MIPI_DPHY_CSI2_RX_D0N |
0.5 V |
|
|
172 |
MIPI_DPHY_CSI1_RX
_D2P |
MIPI_DPHY_CSI2_RX_D0P |
0.5 V |
|
|
173 |
MIPI_DPHY_CSI1_RX
_D1N |
0.5 V |
||
|
174 |
MIPI_DPHY_CSI1_RX
_D1P |
0.5 V |
||
|
175 |
MIPI_DPHY_CSI1_RX
_D0N |
0.5 V |
||
|
176 |
MIPI_DPHY_CSI1_RX
_D0P |
0.5 V |
||
| 177 | VCC_1V8_S3 | 1.8V GPIO kraguitset | Maks 500mA | 1.8 V |
|
178 |
USB2_OTG1_VBUSDE
T |
USB2 VBUS-invoer |
3.3 V |
|
|
179 |
TP_INT_L |
I3C0_SDA_PU_M0/UART10
_RX_M2/SAI0_SDO0_M1/D P_HPD_M1 |
GPIO0_C5_d |
3.3 V |
|
180 |
LCD_BL_PWM1_CH1_
M0 |
I2C1_SDA_M1/UART4_RX_
M2/REFCLK2_OUT |
GPIO0_B5_d/
PWM1_CH1_M0 |
3.3 V |
|
181 |
PCIE1_WAKEn_M0 |
I2C4_SDA_M0/UART1_RTS
_M0/PDM0_SDI3_M0/SAI0_ SDO1/SDI3_M1 |
GPIO0_D3_d/ PWM2_CH0_M0 |
3.3 V |
|
182 |
GPIO0_B4_d |
I2C1_SCL_M1/UART4_TX_
M2/REFCLK1_OUT |
PWM1_CH0_M0 |
3.3 V |
| Speld vas | Sein | Beskrywing of funksies | GPIO reeks | IO Voltage |
|
183 |
USBCC_INT_L |
SPI0_MISO_M0/PDM0_SDI1
_M0/SAI0_SDO3/SDI1_M1 |
GPIO0_D1_d |
3.3 V |
|
184 |
PCIE0_PWREN_H |
I2C3_SDA_M1/SPI0_CLK_M
0/SAI0_LRCK_M1 |
GPIO0_C7_d |
3.3 V |
|
185 |
PCIE0_WAKEn_M0 |
I2C4_SCL_M0/UART1_CTS
_M0/PDM0_SDI2_M0/SAI0_ SDO2/SDI2_M1 |
GPIO0_D2_d/ PWM1_CH5_M0 |
3.3 V |
|
186 |
LCD_PWREN_H |
I2C3_SCL_M1/SPI0_CSn0_
M0/SAI0_SCLK_M1 |
GPIO0_C6_d |
3.3 V |
|
187 |
I2C2_SCL_M0_CC_RT
C |
UART1_TX_M0/PWM1_CH4
_M0(PU2.2K) |
GPIO0_B7_d |
3.3 V |
|
188 |
I2C2_SDA_M0_CC_RT
C |
UART1_RX_M0/PWM1_CH3
_M0(PU2.2K) |
GPIO0_C0_d |
3.3 V |
|
189 |
GPIO0_C4_d |
UART10_TX_M2/PDM0_CL
K0_M0/SAI0_MCLK_M1 |
PWM0_CH0_M0 |
3.3 V |
|
190 |
I2C0_SCL_M1_TP |
I3C0_SCL_M0/UART8_TX_
M2(PU2.2K) |
GPIO0_C1_d |
3.3 V |
|
191 |
I2C0_SDA_M1_TP |
I3C0_SDA_M0/UART8_RX_
M2(PU2.2K) |
GPIO0_C2_d |
3.3 V |
|
192 |
TP_RST_L |
SPI0_MOSI_M0/PDM0_SDI0
_M0/SAI0_SDI0_M1 |
GPIO0_D0_d |
3.3 V |
| 193 | GND | Grond | 0V | |
| 194 | PCIE0_RXP | SATA0_RXP | 0.5 V | |
| 195 | PCIE0_RXN | SATA0_RXN | 0.5 V | |
| 196 | PCIE0_TXN | SATA0_TXN | 0.5 V | |
| 197 | PCIE0_TXP | SATA0_TXP | 0.5 V | |
| 198 | PCIE0_REFCLKP | 0.5 V | ||
| 199 | PCIE0_REFCLKN | 0.5 V | ||
|
200 |
PCIE1_TXP |
SATA1_TXP/USB3_OTG1_S
STXP |
0.5 V |
|
|
201 |
PCIE1_TXN |
SATA1_TXN/USB3_OTG1_S
STXN |
0.5 V |
|
|
202 |
PCIE1_RXP |
SATA1_RXP/USB3_OTG1_S
SRXP |
0.5 V |
|
|
203 |
PCIE1_RXN |
SATA1_RXN/USB3_OTG1_S
SRXN |
0.5 V |
|
| 204 | PCIE1_REFCLKP | 0.5 V | ||
| 205 | PCIE1_REFCLKN | 0.5 V | ||
| 206 | GND | Grond | 0V | |
|
207 |
MIPI_DPHY_CSI4_RX
_CLKP |
0.5 V |
| Speld vas | Sein | Beskrywing of funksies | GPIO reeks | IO Voltage |
|
208 |
MIPI_DPHY_CSI4_RX
_CLKN |
0.5 V |
||
|
209 |
MIPI_DPHY_CSI3_RX
_D3N |
MIPI_DPHY_CSI4_RX_D1N |
0.5 V |
|
|
210 |
MIPI_DPHY_CSI3_RX
_D3P |
MIPI_DPHY_CSI4_RX_D1P |
0.5 V |
|
|
211 |
MIPI_DPHY_CSI3_RX
_D2N |
MIPI_DPHY_CSI4_RX_D0N |
0.5 V |
|
|
212 |
MIPI_DPHY_CSI3_RX
_D2P |
MIPI_DPHY_CSI4_RX_D0P |
0.5 V |
|
|
213 |
MIPI_DPHY_CSI3_RX
_CLKN |
0.5 V |
||
|
214 |
MIPI_DPHY_CSI3_RX
_CLKP |
0.5 V |
||
|
215 |
MIPI_DPHY_CSI3_RX
_D1N |
0.5 V |
||
|
216 |
MIPI_DPHY_CSI3_RX
_D1P |
0.5 V |
||
|
217 |
MIPI_DPHY_CSI3_RX
_D0N |
0.5 V |
||
|
218 |
MIPI_DPHY_CSI3_RX
_D0P |
0.5 V |
||
Ontwikkelingstel (EM3576)
Hardeware-ontwerpgids
Perifere stroombaanverwysing
Eksterne krag
Ontfout stroombaan
HDMI TX stroombaan
Moederbord lengte verstelling
| MIPI CSI0 4-Lane Interface lengte offset | |||
| MIPI_CSI0_RX0_CLKP | MIPI_CSI0_RX0_D0P | (53.5) | (+40) |
| MIPI_CSI0_RX0_D1P | (35.046) | (+30) | |
| MIPI_CSI0_RX0_D2P | |||
| MIPI_CSI0_RX0_D3P | (-25.758) | (-30) | |
Geel blok is CM3576 CSI0 groep lengte verskil.
PCB-voetspoor
Produk Elektriese Eienskappe
Dissipasie en temperatuur
| Simbool | Parameter | Min | Tipe | Maks | Eenheid |
|
VCC_SYS |
Stelsel Voltage |
3.4 V |
4 |
5.5 |
V |
|
Isys_in |
VCC_SYS
invoer Huidige |
1750 |
mA |
||
|
VCC_RTC |
RTC Voltage |
1.8 |
3 |
3.4 |
V |
|
Iirtc |
RTC-invoer
Huidige |
5 |
8 |
uA |
|
|
I3v3_uit |
VCC_3V3
uitset Huidige |
500 |
mA |
||
|
I1v8_uit |
VCC_1V8
uitset Huidige |
500 |
mA |
||
|
Ta |
Bedryfstemperatuur |
0 |
70 |
°C |
|
|
Tstg |
Bergingstemperatuur |
-40 |
85 |
°C |
Betroubaarheid van toets
| Hoë temperatuur bedryfstoets | ||
| Inhoud | Werk 8 uur in hoë temperatuur | 55 ° C ± 2 ° C |
| Resultaat | TBD | |
| Bedryfslewe toets | ||
| Inhoud | Bedryf in kamer | 120h |
| Resultaat | TBD | |
Dokumente / Hulpbronne
 |
Boardcon CM3576-stelsel op module [pdfGebruikershandleiding CM3576 Stelsel op Module, CM3576, Stelsel op Module, Module |
