Tenmars TM-901N LAN Cable Tester User Manual

1. Inleiding

The Tenmars TM-901N is a professional LAN cable tester designed for efficient and accurate diagnosis of network cable issues. It is capable of identifying various wiring faults such as discontinuity, short-circuits, incorrect connections, and split pairs in both Shielded Twisted Pair (STP) and Unshielded Twisted Pair (UTP) cables. This device can measure cable lengths up to 265 meters, making it an essential tool for network installers and technicians.

2. Veiligheidsinligting

Lees en verstaan ​​asseblief alle veiligheidsinstruksies voordat u die toestel gebruik. Versuim om hierdie instruksies te volg, kan lei tot besering of skade aan die toestel.

• Do not attempt to test live circuits or cables connected to active network equipment.
• Ensure the battery is correctly installed before use.
• Moenie die toestel aan vog of uiterste temperature blootstel nie.
• Moenie die toestel oopmaak nie casing, aangesien dit die waarborg ongeldig kan maak en u aan elektriese gevare kan blootstel.
• Gooi batterye weg volgens plaaslike regulasies.

3. Pakketinhoud

Verifieer dat alle items in jou pakket teenwoordig is:

• Tenmars TM-901N Main Unit
• Remote ID Locator (ID 1)
• Gebruikershandleiding (hierdie dokument)
• Note: A 9V battery is typically required and may not be included.

Image 3.1: Tenmars TM-901N Main Unit and Remote ID Locator.

4. Produk verbyview

4.1 Hoofeenheid

Beeld 4.1: Voorkant view of the TM-901N Main Unit.

The main unit features an LCD display for showing test results and cable status. It includes several control buttons:

• TOETS-knoppie: Initiates a cable test.
• L/W Button: Toggles between Length measurement and Wiremap display modes.
• SET/UNIT Button: Used to enter settings mode and change measurement units (e.g., meters, feet).
• Pyltjieknoppies (Links/Regs): Used for navigation in settings or for reviewtoetsresultate.

4.2 Remote ID Locator

Image 4.2: Remote ID Locator.

The remote ID locator is a passive unit used in conjunction with the main unit to test installed cables. It connects to one end of the cable while the main unit connects to the other. The remote unit is labeled "ID 1" for identification.

4.3 Rear Panel and Wiring Diagram

Prent 4.3: Agter view of the TM-901N Main Unit with wiring diagram.

The rear panel of the main unit includes the battery compartment and a printed wiring diagram for reference, showing standard T568A/B pin assignments for RJ45 connectors.

5. Opstelling

5.1 Battery installasie

1. Locate the battery compartment cover on the rear of the main unit.
2. Slide the cover open or remove it as indicated.
3. Plaas 'n nuwe 9V-battery in en maak seker dat die polariteit (+/-) korrek is.
4. Plaas die batterykompartement se deksel veilig terug.

Image 5.1: Battery compartment with cover removed.

5.2 Connecting Cables for Testing

Before connecting any cables, ensure they are disconnected from all active network devices.

• For patch cables (uninstalled cables): Connect one end of the cable to the RJ45 port on the main unit and the other end to the RJ45 port on the remote ID locator.
• For installed cables: Connect the main unit to one end of the installed cable (e.g., a wall jack) and the remote ID locator to the other end of the cable (e.g., in a patch panel).

6. Bedryfsinstruksies

6.1 Aan-/afskakel

The device typically powers on automatically when a cable is connected and the TEST button is pressed, or by pressing the TEST button. It usually powers off automatically after a period of inactivity to conserve battery.

6.2 Performing a Cable Test

1. Ensure the cable is properly connected to the main unit and the remote ID locator.
2. Druk die TOETS knoppie.
3. The tester will automatically scan the cable and display the results on the LCD.

6.3 Interpreting Test Results (Wiremap)

The LCD will display the wiremap, indicating the connection status of each wire pair. Common indications include:

• Slaag: All wires are correctly connected (1-1, 2-2, etc. for straight-through, or appropriate cross-over mapping).
• Open/Discontinuity: A break in one or more wires. The display will show which wire(s) are open.
• Short-Circuit: Two or more wires are touching. The display will indicate the shorted wires.
• Incorrect Connection/Miswire: Wires are connected to the wrong pins at one or both ends. The display will show the incorrect mapping (e.g., 1-3, 2-6).
• Verdeel pare: A more complex fault where two pairs are swapped, but the wiremap appears correct. The tester is designed to detect this.

6.4 Measuring Cable Length

1. After performing a test, press the L/W button to switch to Length measurement mode.
2. The display will show the estimated length of the cable.
3. To change the unit of measurement (meters, feet), press the SET/UNIT button while in Length mode and use the arrow buttons to select the desired unit. Press SET/UNIT weer om te bevestig.

7. Onderhoud

7.1 Skoonmaak

Wipe the device with a soft, dry cloth. Do not use abrasive cleaners or solvents. Ensure no moisture enters the device.

7.2 Batteryvervanging

When the battery low indicator appears on the display, replace the 9V battery as described in Section 5.1. Remove the battery if the device will not be used for an extended period to prevent leakage.

7.3 Berging

Bêre die toestel op 'n koel, droë plek, weg van direkte sonlig en uiterste temperature. Hou dit in sy oorspronklike verpakking of 'n beskermende houer wanneer dit nie gebruik word nie.

8. Probleemoplossing

9. Spesifikasies

10. Waarborg en Ondersteuning

For warranty information and technical support, please refer to the documentation provided with your purchase or contact your local distributor. Keep your proof of purchase for warranty claims.