KICKER 48TRTP122 Subwoofer and DS18 CANDY-X1B Amplewendiger stelsel gebruikershandleiding

1. Produk verbyview

This manual provides instructions for the KICKER 48TRTP122 12-inch CompRT Down-Firing Loaded Subwoofer Enclosure, the DS18 CANDY-X1B Mono Class D Amplifier, and the accompanying DS18 AMPKIT4 4AWG Complete Amplifier Wiring Kit. This system is designed to enhance your vehicle's audio experience with powerful bass output.

2. Wat is in die boks

• Kicker 48TRTP122 12" CompRT Series Down-Firing Loaded Subwoofer Enclosure
• DS18 CANDY-X1B Mono Candy-X Series Car Amplewendiger
• DS18 AMPKIT4 4AWG Complete Amplifier Kit, including:
  • 17 ft 4 AWG Red Power Wire
  • 3 ft 4 AWG Black Ground Wire
  • 17 ft Remote Wire
  • 17 ft Red/Black Speaker Cable
  • 17 ft Red/Black Twisted RCA Cable
  • Mini ANL Fuse Holder with Mini ANL 100A Fuse
  • 6 ft 4 AWG Loom Tube
  • 1 x Rubber Grommet
  • 10 x Kabelbinders
  • 2 x Ringterminale
  • 2 x Spade Terminale
  • 5 x Small Spade Terminals

Figure 2.1: Components of the DS18 AMPKIT4 4AWG Complete Ampverligter Kit.

3. Opstelling en installering

Behoorlike installasie is noodsaaklik vir optimale werkverrigting en veiligheid. Indien u onseker is oor enige stappe, raadpleeg 'n professionele motor-klankinstalleerder.

3.1 Veiligheidsmaatreëls

• Ontkoppel die voertuig se negatiewe batteryklem voordat u enige elektriese werk begin.
• Maak seker dat alle bedrading behoorlik geïsoleer en vasgemaak is om kortsluitings en skade te voorkom.
• Gebruik gepaste persoonlike beskermende toerusting (PPE) tydens installasie.

3.2 Subwoofer Enclosure Placement

The KICKER 48TRTP122 is a down-firing enclosure, designed to be placed in the trunk or cargo area of your vehicle. Ensure it is securely fastened to prevent movement during driving.

Figure 3.1: KICKER 48TRTP122 Down-Firing Subwoofer Enclosure.

3.3 Amplewendiger montering

Mount the DS18 CANDY-X1B amplifier in a location that allows for adequate ventilation and protection from moisture. Common locations include under a seat, in the trunk, or on the back of a rear seat. Ensure it is securely mounted to prevent vibration damage.

Figure 3.2: DS18 CANDY-X1B Mono Class D Amplewendiger.

3.4 Bedradingsinstruksies

Follow these steps carefully for wiring the system. Refer to the wiring diagram below for visual guidance.

1. Power Wire (Red 4 AWG): Run the 17 ft red power wire from the vehicle's positive battery terminal to the fuse holder, then from the fuse holder to the +12V terminal on the DS18 amplifier. Ensure the fuse holder is installed close to the battery (within 18 inches).
2. Ground Wire (Black 4 AWG): Connect the 3 ft black ground wire from the GND terminal on the ampVerwyder die laaier na 'n skoon, ongeverfde metaaloppervlak op die voertuig se onderstel. Verseker 'n goeie elektriese verbinding.
3. Draad vir afstandaanskakeling: Connect the remote wire from your head unit's remote output to the REM terminal on the ampverligter. Hierdie draad draai die amplifer aan en af ​​met jou hoof-eenheid.
4. RCA-kabels: Connect the RCA cables from your head unit's subwoofer output (or full-range output if no dedicated sub output) to the RCA input jacks on the DS18 amplewendiger.
5. Luidsprekerdraad: Koppel die luidsprekerkabel van die amplifier's speaker output terminals to the KICKER subwoofer enclosure's input terminals. Ensure correct polarity (+ to + and - to -). The KICKER 48TRTP122 enclosure has a 2-ohm impedance.
6. Bas afstandsbediening: Connect the included bass remote to the dedicated remote port on the DS18 amplifier. Mount the remote in an accessible location for easy adjustment.

Figure 3.3: Subwoofer to Amplifier Wiring Diagram (2-ohm connection).

Figure 3.4: DS18 Bass Remote Control.

4. Bedryfsinstruksies

Once the system is installed, follow these steps to configure and operate your subwoofer and amplewendiger.

4.1 Initial Power-Up and Gain Setting

1. Koppel die voertuig se negatiewe batteryklem weer aan.
2. Skakel jou hoofeenheid aan. Die amplifier should power on (indicated by a blue LED on the amplewendiger).
3. Stel die amplifier's GAIN control to its minimum (fully counter-clockwise) position.
4. Play a music track with strong bass at a moderate volume level on your head unit (around 75% of maximum volume).
5. Verhoog die GAIN-beheer stadig op die amplifier until you hear distortion, then back it off slightly until the sound is clear. This sets the maximum clean output level.

4.2 Amplifier Controls (DS18 CANDY-X1B)

The DS18 CANDY-X1B amplifier features several controls for fine-tuning your bass output:

• WINS: Adjusts the input sensitivity to match the output of your head unit. (See 4.1)
• BASS BOOST (0-18 dB): Increases the bass output at a specific frequency (typically around 45 Hz). Use sparingly to avoid distortion and speaker damage.
• LPF (Low-Pass Filter) (50-150 Hz): This filter allows only frequencies below the set point to pass through to the subwoofer. Adjust to blend the subwoofer's output seamlessly with your main speakers.
• SUBSONIC FILTER (10-55 Hz): Filters out extremely low frequencies that are inaudible and can cause damage to the subwoofer. Set it slightly below your subwoofer's lowest usable frequency.
• PHASE (0/180 degrees): Adjusts the phase of the subwoofer output relative to your main speakers. Experiment with both settings to find the one that provides the most impactful and coherent bass.
• AFGELEË: Port for connecting the wired bass remote control, allowing convenient bass level adjustment from the driver's seat.

Figure 4.1: DS18 CANDY-X1B Amplifier Controls.

5. Onderhoud

Regular maintenance ensures the longevity and optimal performance of your audio system.

• Skoonmaak: Keep the subwoofer enclosure and amplifier clean and free of dust and debris. Use a soft, dry cloth. Avoid liquid cleaners directly on components.
• Verbindings: Kontroleer gereeld alle bedradingsverbindings vir styfheid en korrosie. Los verbindings kan lei tot swak werkverrigting of skade.
• Ventilasie: Verseker die ampDie koelvinne van die verkoeler word nie geblokkeer om oorverhitting te voorkom nie.
• Sit sekering: As die amplifier does not power on, check the fuse in the fuse holder near the battery. Replace with a fuse of the same rating (100A Mini ANL).

6. Probleemoplossing

Verwys na hierdie afdeling vir algemene probleme en hul oplossings.

7. Spesifikasies

Detailed specifications for the components in this bundle.

7.1 KICKER 48TRTP122 12" CompRT Subwoofer Enclosure

• Tipe luidspreker: Subwoofer
• Subwoofer deursnee: 12 duim
• Piek krag: 1000 watt
• RMS-krag: 500 watt
• Impedansie: 2 ohm
• Sensitiwiteit: 98dB
• Spesiale kenmerk: Down-Firing, Active thin-mount CompRT subwoofer, High-output reFLEX passive woofer
• Materiaal: Mediumdigtheid veselbord
• Afmetings: 27.5" W x 6.125" H x 14.625" D (Top) x 14.625" D (Bottom)

7.2 DS18 CANDY-X1B Mono Class D Amplewendiger

• RMS-kraggradering:
  • 4 ohms: 240 watts x 1 channel
  • 2 ohms: 400 watts x 1 channel
  • 1 ohm: 600 watts x 1 channel
• Maksimum kraguitset: 1800 watt
• Sensitiwiteit: 100dB
• Frekwensie reaksie: 20-150 Hz
• Bas afstandsbediening: Ingesluit
• Ontwerp: Klas D
• Veranderlike basversterking: 0-18 dB
• Variable Low-pass filter (LPF): 50-150 Hz
• Subsoniese filter: 10-55 Hz
• Afmetings: 5.9" B x 8.3" D x 2.16" H

7.3 DS18 AMPKIT4 4AWG Complete Ampverligter Kit

• Draadmeter: 4 AWG
• Draad materiaal: High Performance CCA (Copper Clad Aluminum)
• Aanbeveel vir: Een amplifier up to 1300 Watts
• Ingesluit komponente: Power wire, ground wire, remote wire, speaker cable, RCA cable, fuse holder with 100A fuse, loom tube, grommet, cable ties, various terminals.

8. Waarborginligting

This product bundle typically comes with a manufacturer's warranty. The KICKER 48TRTP122 subwoofer enclosure and DS18 CANDY-X1B amplifier are covered by a full warranty from their respective manufacturers. Specific warranty terms, duration, and coverage details may vary. Please retain your proof of purchase for warranty claims.

For detailed warranty information, refer to the documentation included with each individual component or visit the respective manufacturer's official webwebwerf.

9. Ondersteuning

If you encounter issues not covered in this manual or require further assistance, please contact the manufacturer's customer support:

• KICKER Support: Visit the official KICKER webwebwerf vir ondersteuningsbronne, algemene vrae en kontakbesonderhede.
• DS18 Support: Visit the official DS18 website for product support and contact details.

When contacting support, please have your product model numbers (48TRTP122, CANDY-X1B, AMPKIT4) and proof of purchase readily available.