eSUN eBox-Lite-US
eSUN eBOX Lite Upgraded 3D Printing Filament Dryer Box User Manual
Model: eBox-Lite-US
1. Produk verbyview
The eSUN eBOX Lite is an upgraded filament dryer box designed to maintain optimal conditions for 3D printing filaments. It effectively removes moisture, preventing common printing issues such as stringing, clogging, and poor adhesion. This device also functions as a filament storage box and spool holder, providing a comprehensive solution for filament management.
Key features include efficient heating, even temperature distribution, low-noise operation, and broad compatibility with various filament types and spool sizes.
Figure 1: eSUN eBOX Lite Filament Dryer Box with a red filament spool inside.
2. Pakketinhoud
Verifieer dat alle items in die pakket teenwoordig is:
- eBOX Lite Dryer Box
- Kragadapter (VS-prop)
- User Manual (this document, and a physical copy)
- Filament Outlet Tube/Bayonet
Figure 2: Illustration of the eBOX Lite and its included accessories.
3. Opstelinstruksies
- Plasing: Place the eBOX Lite on a stable, flat surface away from direct sunlight, heat sources, and excessive humidity. Ensure adequate ventilation around the unit.
- Kragverbinding: Connect the provided power adapter to the DC input port on the back of the eBOX Lite. Plug the adapter into a standard US power outlet (AC100-240V ~ 50/60Hz).
- Laai filament:
- Open the transparent lid of the eBOX Lite.
- Place your filament spool onto the internal rollers. Ensure the spool rotates freely. The maximum compatible spool size is Φ200mm (diameter) x 73mm (height).
- Thread the filament through the designated outlet hole on the lid. If using the outlet conduit, attach it to the hole and thread the filament through it.
- Maak die deksel stewig toe.
Figure 3: Visual guide for connecting power and loading filament.
4. Bedryfsinstruksies
The eBOX Lite features a simple control panel with a display and buttons for setting temperature and time.
4.1. Beheerpaneel verbyview
- Vertoon: Shows current settings (temperature level, time remaining).
- Modusknoppie: Used to cycle between temperature setting mode and time setting mode.
- Op/af knoppies: Used to adjust values (temperature level, time).
4.2. Temperatuur en Tyd instel
- Krag aan: After connecting the power, the display will light up.
- Set Temperature Level:
- Druk die Modus button once to enter temperature setting mode. The display will show a number (1, 2, or 3).
- Gebruik die Op/af buttons to select the desired temperature level based on your filament type:
- Vlak 1: Approximately 40°C (suitable for PLA/PLA+)
- Vlak 2: Approximately 50°C (suitable for ABS/ABS+/PETG)
- Vlak 3: Approximately 55°C (suitable for PVA/Nylon/PC)
- Druk die Modus button again to confirm the temperature level and proceed to time setting.
- Set Heating Time:
- The display will now show the time setting (e.g., "00.0h").
- Gebruik die Op/af buttons to set the desired heating duration from 0 to 18 hours. For optimal drying, eSUN recommends at least 2 hours for most filaments.
- Druk die Modus button again to start the drying process. The display will show the remaining time.
The eBOX Lite will maintain the set temperature and humidity throughout the drying cycle. Once the time expires, the heating will stop, but the box will continue to provide a dry storage environment.
Figure 4: Recommended temperature levels and corresponding filament types.
Figure 5: Graph illustrating humidity reduction over time during drying.
5. Onderhoud
Regular maintenance ensures the longevity and optimal performance of your eBOX Lite.
- Skoonmaak: Vee die buitekant van die eenheid af met 'n sagte, droë lap. Moenie skuurmiddels of oplosmiddels gebruik nie. Maak seker dat die eenheid ontkoppel is voor skoonmaak.
- Interne skoonmaak: Periodically check the inside of the box for any dust or filament debris. Use a soft brush or compressed air to remove any accumulation.
- Berging: Wanneer dit vir lang tye nie gebruik word nie, koppel die toestel uit en stoor dit op 'n koel, droë plek.
6. Probleemoplossing
| Probleem | Moontlike oorsaak | Oplossing |
|---|---|---|
| Toestel skakel nie aan nie. | Kragadapter nie gekoppel of foutief nie; probleem met kragaansluiting. | Ensure power adapter is securely connected. Try a different power outlet. Check if the power adapter is damaged. |
| Filament not drying effectively. | Incorrect temperature level set; insufficient drying time; lid not closed properly. | Verify the correct temperature level for your filament type. Increase drying time (e.g., to 4-6 hours or more for very wet filament). Ensure the lid is fully closed. |
| Die skerm is leeg of reageer nie. | Temporary software glitch; power interruption. | Unplug the device, wait 30 seconds, then plug it back in. If the issue persists, contact customer support. |
| Filament spool does not rotate smoothly. | Spool too large or not seated correctly; debris on rollers. | Ensure spool dimensions are within specifications (Φ200mm x 73mm). Re-seat the spool. Clean the rollers. |
7. Spesifikasies
| Parameter | Waarde |
|---|---|
| Modelnommer | eBox-Lite-US |
| Binne temperatuurreeks | 40°C - 55°C |
| Hot Plate Temperature | 105°C - 118°C |
| Gegradeerde krag | AC100-240V ~ 50/60Hz |
| Kraguitset | DC24V ~ 2A |
| Krag van verwarmer | 35 W |
| Produk Gewig | 0.75 kg (1.65 pond) |
| Produk Grootte | 215 x 104 x 238.5 mm |
| Pakket afmetings | 10.91 x 10 x 5.51 duim |
| Max Spool Capacity | Φ200mm (diameter) x 73mm (height) |
| Compatible Filament Diameter | 1.75mm / 2.85mm / 3.00mm |
| Materiaal tipe | Polikarbonaat |
Figure 6: Detailed product specifications and package contents.
8. Waarborg en Ondersteuning
For warranty information and technical support, please refer to the official eSUN webwebwerf of kontak hul kliëntediens direk. Bewaar u aankoopbewys as bewys van aankoop.
You can also find additional resources and a PDF version of the user manual at: eSUN eBOX Lite User Manual (PDF)
Verwante Dokumente - eBox-Lite-US
 |
eSUN eBOX 3D Printing Filament Dryer User Guide User guide for the eSUN eBOX filament dryer, covering setup, operation modes (Gram, Pound, WOC, TEMP, TIME), parameter settings, and specifications for 3D printing filament. |
 |
eSUN eBOX Lite User Guide for 3D Printer Filament Dry Box Comprehensive user guide for the eSUN eBOX Lite, a filament dry box designed to keep 3D printer filaments in optimal condition. Learn about its features, specifications, operation, and parameter settings for various filament types. |
 |
eSUN eBOX Pro 3D Printing Filament Dryer User Guide Official user guide for the eSUN eBOX Pro filament dryer. Learn how to safely operate, set up, and optimize your 3D printing filament drying process. |
 |
eSUN 3D-drukmateriaal: Omvattende produkkatalogus en gids Verken eSUN se uitgebreide reeks 3D-drukfilamente, insluitend PLA, PETG, ABS en spesiale materiale. Ontdek produkvoordeletages, toepassings en sertifikate vir al u 3D-drukbehoeftes. |
 |
eSUN PEBA-90A Thermoplastic Elastomer Filament Technical Data Sheet Technical data sheet for eSUN PEBA-90A, a high-performance thermoplastic elastomer filament for 3D printing, detailing its properties, applications, and recommended printing parameters. |
 |
eSUN eVacuum Kit Pro 3 User Manual: 3D Filament Vacuum Storage Guide Comprehensive user manual for the eSUN eVacuum Kit Pro 3, detailing its use, specifications, and troubleshooting for vacuum storage of 3D printer filament. Preserves filament quality by preventing moisture absorption. |
Ask a question about this manual
Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.