Docooler JINGSHA X99-8D3 Motherboard User Manual

1. Inleiding en oorview

The Docooler JINGSHA X99-8D3 is a high-performance ATX gaming motherboard designed for LGA2011 V3 processors. It features four-channel DDR3 memory support, an M.2 NVME slot for high-speed storage, and multiple PCI-E expansion slots, making it suitable for demanding computing tasks and gaming setups. This manual will guide you through the installation, configuration, and maintenance of your motherboard.

Figuur 1.1: Bo-na-onder view of the Docooler JINGSHA X99-8D3 Motherboard, showcasing its layout with CPU socket, RAM slots, and various expansion slots.

2. Sleutel kenmerke

• M.2 NVME Support: Equipped with an M.2 hard disk port, supporting high-speed PCI-E NVME X4 for optimal operating system and application driver performance.
• Quad-Channel DDR3 Memory: Features 8 DDR3 memory slots across 4 channels, significantly improving capacity and performance, supporting up to 256GB.
• Digital Diagnostic Card: Integrated digital diagnostic card automatically tests hardware devices to ensure proper operation and assist in troubleshooting.
• Multiple PCI-E Expansion Slots: Provides 3 PCI-E expanded slots, configurable as X16/X8 to handle various workloads and multi-GPU setups.
• Duursame konstruksie: Built with a 10-layer PCB and high-quality capacitors for enhanced stability and heat resistance.

Figure 2.1: Diagram illustrating the six core technologies and features of the motherboard, including 4-channel DDR3*8, M.2 hard disk interface, digital diagnostic card, 7.1 channel audio, SATA3.0*8 interface, and Crossfire support.

3. Pakketinhoud

Verifieer asseblief dat al die items wat hieronder gelys word, in u pakket teenwoordig is:

• 1x Docooler JINGSHA X99-8D3 Motherboard
• 1x SATA-kabel
• 1x I/O Baffle (Backplate)
• 1x CPU Fan Board
• A bag of screws

4. Spesifikasies

Figuur 4.1: Gedetailleerd view of the motherboard's rear I/O panel, showing PS/2 ports, USB 2.0, USB 3.0, Gigabit Network Port, and 7.1 Audio Ports.

5. Opstelling en installering

Voordat u met die installasie begin, maak seker dat u stelsel afgeskakel en uit die muurprop ontkoppel is. Hanteer die moederbord aan die kante om statiese ontlading te vermy.

5.1 Die installering van die SVE

1. Locate the LGA2011 V3 CPU socket on the motherboard.
2. Gently push down the CPU retention lever and swing it open.
3. Align the triangular mark on your CPU with the corresponding mark on the socket. Carefully place the CPU into the socket without forcing it.
4. Maak die retensiehefboom toe om die SVE vas te maak.
5. Wend 'n dun, egalige laag termiese pasta aan die bokant van die SVE.
6. Install the CPU cooler according to its manufacturer's instructions, ensuring proper contact and pressure.

Figuur 5.1: Close-up view of the LGA2011 V3 CPU socket on the motherboard, ready for CPU installation.

5.2 RAM-modules installeer

1. Maak die knippies aan beide kante van die DDR3-geheuegleuwe oop.
2. Rig die kerf op die RAM-module met die sleutel in die geheuegleuf.
3. Press down firmly on both ends of the RAM module until the clips snap into place, securing the module.
4. For optimal performance, install RAM modules in matching pairs across the four channels as indicated in the motherboard manual or silkscreen.

Figuur 5.2: View of the eight DDR3 RAM slots on the motherboard, showing their arrangement for quad-channel memory configuration.

5.3 Installing Storage Devices (M.2 NVME & SATA)

1. M.2 NVME SSD: Locate the M.2 slot. Insert the M.2 SSD at an angle into the slot, then gently push it down and secure it with the provided screw.
2. SATA-skywe: Connect your SATA SSDs or HDDs to the SATA 3.0 ports using SATA data cables. Ensure the power supply SATA power connectors are also attached to the drives.

Figure 5.3: Close-up of the M.2 interface on the motherboard, highlighting its position and the PCI-E Gen3 X4 connection for high-speed data transfer.

Figuur 5.4: View of the eight orange SATA 3.0 ports on the motherboard, providing ample connectivity for storage devices.

5.4 Aansluiting van kragtoevoer

1. Koppel die 24-pen ATX-kragkonnektor van jou kragtoevoereenheid (PSU) aan die ooreenstemmende poort op die moederbord.
2. Connect the 8-pin CPU power connector (EPS12V) from your PSU to the 8-pin port near the CPU socket.

5.5 Installing Expansion Cards (PCIe)

1. Locate the desired PCI-E 3.0 x16 or x1 slots.
2. Verwyder die ooreenstemmende uitbreidingsgleufdeksel van jou rekenaarkas.
3. Align the expansion card with the slot and press down firmly until it is fully seated. Secure the card with a screw to the case.

Figuur 5.5: Hoekig view of the motherboard, highlighting the three PCI Express 3.0 x16 slots and the smaller PCIe x1 slots, ready for graphics cards and other expansion cards.

6. Bediening van die moederbord

6.1 Eerste opstart en BIOS-opstelling

1. Nadat u al die komponente saamgestel het, koppel u monitor, sleutelbord en muis.
2. Power on your system. During the initial boot sequence, repeatedly press the DEL or F2 key (common for JINGSHA motherboards) to enter the BIOS/UEFI setup utility.
3. Verifieer in die BIOS dat alle geïnstalleerde komponente (SVE, RAM, stoorplek) korrek opgespoor word.
4. Configure boot order to prioritize your operating system installation media (USB drive or DVD).
5. Stoor veranderinge en verlaat BIOS. Die stelsel sal herbegin.

6.2 Bedryfstelsel installasie

Follow the instructions provided with your operating system (e.g., Windows, Linux) to complete the installation process. Ensure you install all necessary drivers for the motherboard's chipsets, network, audio, and other components from the manufacturer's website or included driver disc.

7. Onderhoud

Behoorlike onderhoud verseker die lang lewensduur en stabiele werking van jou moederbord.

• Stofverwydering: Maak gereeld stof van die moederbord en komponente skoon met saamgeperste lug. Maak seker dat die stelsel afgeskakel en ontkoppel is voordat jy dit skoonmaak.
• BIOS-opdaterings: Periodically check the Docooler or JINGSHA official website for BIOS updates. BIOS updates can improve compatibility, stability, and performance. Follow update instructions carefully to avoid damaging the motherboard.
• Bestuurderopdaterings: Hou jou stelseldrywers opgedateer om optimale werkverrigting en versoenbaarheid met nuwe sagteware en hardeware te verseker.
• Omgewingstoestande: Operate the motherboard in a well-ventilated environment with stable temperature and humidity to prevent overheating and component degradation.

8. Probleemoplossing

Hierdie afdeling spreek algemene probleme aan wat jy mag teëkom.

8.1 Geen krag / Geen opstart

• Maak seker dat die 24-pen ATX- en 8-pen SVE-kragkonnektore stewig in die moederbord ingeprop is.
• Check if the power supply unit (PSU) is switched on and connected to a working power outlet.
• Verify that the front panel power button cable is correctly connected to the motherboard's header.

8.2 Geen skermuitvoer nie

• Ensure your graphics card (if dedicated) is properly seated in its PCI-E slot and has all necessary power cables connected.
• Check that your monitor cable is securely connected to the graphics card or motherboard (if integrated graphics are used, though X99 typically requires a dedicated GPU).
• Try reseating your RAM modules. Incorrectly seated RAM is a common cause of no display.

8.3 POST Code Display (Digital Diagnostic Card)

The motherboard is equipped with a digital diagnostic card (POST code display) that shows a two-digit code during boot-up. Refer to the motherboard's detailed technical documentation (often available on the manufacturer's website) for a list of POST codes and their meanings. This can help pinpoint the exact component causing a boot failure.

Figuur 8.1: Close-up view showing the integrated digital diagnostic card (POST code display) on the motherboard, which assists in identifying hardware issues during boot.

9. Waarborg en Ondersteuning

For warranty information and technical support, please refer to the documentation provided with your purchase or visit the official Docooler or JINGSHA webwebwerf. Bewaar u bewys van aankoop vir waarborgeise.