ACEGMET X20-60m Green Beam Laser Measure User Manual

1. Inleiding

The ACEGMET X20-60m is a portable and user-friendly green beam laser measuring device designed for high-precision distance measurements. It features a bright green laser for enhanced visibility, an electronic angle sensor for advanced measurements, and multiple calculation modes including area, volume, and Pythagorean functions. This manual provides essential information for the safe and effective operation of your device.

Image: The ACEGMET X20-60m Green Beam Laser Measure device.

2. Veiligheidsinligting

This device uses a Class 2 laser. Observe the following safety precautions:

• Moenie direk in die laserstraal staar nie.
• Moenie die laserstraal op mense of diere rig nie.
• Vermy direkte oogblootstelling.
• Do not disassemble the device; repairs should only be performed by authorized personnel.
• Hou die toestel buite bereik van kinders.
• Gebruik die toestel slegs vir sy beoogde doel soos beskryf in hierdie handleiding.

Laser klas: Klas 2
Laser tipe: 490-560nm, <1mW

3. Pakketinhoud

Verifieer dat alle items in die pakket teenwoordig is:

• 1x ACEGMET Laser Measure Device
• 3x 1.5V Rechargeable Batteries
• 1x Handband
• 1x stoor sak

Image: The ACEGMET X20-60m laser measure, rechargeable batteries, hand strap, and storage bag.

4. Opstelling

4.1 Battery installasie

1. Vind die batterykompartement op die toestel.
2. Maak die batteryvakdeksel oop.
3. Insert the three 1.5V rechargeable batteries, ensuring correct polarity (+/-).
4. Maak die batterykompartement se deksel stewig toe.

4.2 Laai die toestel

The device is equipped with rechargeable batteries and supports USB charging.

1. Koppel die meegeleverde USB-kabel aan die laaipoort op die toestel.
2. Koppel die ander kant van die USB-kabel aan 'n versoenbare USB-kragadapter (nie ingesluit nie) of 'n rekenaar se USB-poort.
3. The device's display will indicate charging status.
4. Sodra dit volledig gelaai is, ontkoppel die USB-kabel.

Image: The laser measure connected for USB charging, highlighting its waterproof design.

5. Bedryfsinstruksies

5.1 Krag aan/af

• Om aan te skakel: Druk die MEAS knoppie.
• Om af te skakel: Druk en hou die GAAN WEG button. The device will automatically shut down after 180 seconds of inactivity to save power.

5.2 Eenheidskakeling

Druk die EENHEID button to cycle through measurement units: Meters (M), Inches (In), Feet (Ft), and Feet+Inches (Ft+In).

5.3 Reference Point Switching

The device can measure from its front or rear edge. Press the reference point button (often indicated by an icon with an arrow pointing from the front or back of the device) to switch between reference points as needed for different measurement scenarios.

5.4 Meetmodusse

Druk die Funksie button (often indicated by a square icon or 'M' for Mode) to cycle through the available measurement modes.

Image: Visual representation of the eight measurement modes and four unit modes available on the device.

1. Enkelafstandmeting:

   Rig die laser op die teiken en druk MEAS. The distance will be displayed instantly.
2. Deurlopende Meting (Spooring):

   Activate this mode, then move the device. The display will continuously update with the current distance, showing maximum and minimum values.

3. Oppervlaktemeting:

   Select area mode. Measure the length, then measure the width. The device will automatically calculate and display the area.

4. Volumemeting:

   Select volume mode. Measure length, width, and height. The device will automatically calculate and display the volume.
5. Pythagorean Measurement (2-point, 3-point):

   Used for indirect height or distance measurements. Follow the on-screen prompts to measure the required sides of a right-angled triangle. The device will calculate the unknown side.

6. Electronic Angle Sensor / Auto Level / Auto Height Measurement:

   The integrated angle sensor allows for electronic level measurements, auto-level, and auto-height functions. For example, measure the distance between two points in the horizontal direction or determine the height of a window from the ground with a single measurement.

   

   Image: Demonstrating the angle sensor measurement feature to calculate the height of a window.

5.5 Databerging en -herwinning

The device can store up to 20 sets of measurement data. Use the appropriate buttons (refer to device interface) to save and retrieve historical data.

Image: The device display showing multiple stored measurement data records.

5.6 Optelling en Aftrekking

The device supports addition and subtraction of measurement values. Enter the first value, select the addition/subtraction function, then enter the second value. The result will be displayed.

5.7 Dempfunksie

For use in quiet environments, activate the mute function to disable audible feedback.

5.8 Backlit LCD Display

The 2-inch backlit LCD display provides clear visibility in low light conditions.

6. Onderhoud

6.1 Skoonmaak

• Vee die toestel af met 'n sagte, damp lap. Moenie skuur skoonmaakmiddels of oplosmiddels gebruik nie.
• Ensure the laser lens and display are clean for accurate readings.

6.2 Berging

• Store the device in its storage bag when not in use.
• Hou die toestel op 'n koel, droë plek, weg van direkte sonlig en uiterste temperature.

6.3 Self-kalibrasie

The device supports self-calibration to maintain measurement accuracy. Refer to the on-screen menu or specific button combinations for initiating the self-calibration process.

7. Probleemoplossing

• Toestel word nie aangeskakel nie: Check battery charge level. Ensure batteries are inserted correctly.
• Onakkurate metings: Ensure the laser lens is clean. Verify the correct reference point is selected. Perform self-calibration if necessary.
• Laserstraal nie sigbaar nie: The green beam is designed for better visibility, but in very bright conditions or over long distances, it may be less apparent. Ensure the target surface is suitable for reflection.
• Foutboodskappe: Consult the device's display for specific error codes and refer to the full product manual (if available) for detailed explanations.

8. Spesifikasies

9. Waarborg en Ondersteuning

ACEGMET provides an 18-month worry-free warranty and lifetime technical support for this product. If you have any questions or require assistance, please contact ACEGMET customer service. Our technical and after-sales teams are available to assist you.