Kwikset SmartCode 888 Electronic Deadbolt Door Lock User Manual

Inleiding

The Kwikset SmartCode 888 Electronic Deadbolt Door Lock offers keyless entry and smart home integration. This device allows users to lock or unlock their door using a personalized code on the touchpad or remotely through a compatible smart home system. It features Z-Wave Plus technology for wireless communication and SmartKey Security for re-keying convenience. This manual will guide you through the installation, operation, and maintenance of your new lock.

Figure 1: Kwikset SmartCode 888 Electronic Deadbolt, exterior view.

Veiligheidsinligting

• Always use a manual screwdriver for installation. Do not use an electric drill or an electric screwdriver to tighten screws, as this can damage the lock and void the warranty.
• Ensure all components are installed correctly and securely before operating the lock.
• Hou batterye weg van kinders en gooi dit op die regte manier weg.

Installasiegids

This section provides a step-by-step guide for installing your Kwikset SmartCode 888 electronic deadbolt. For a visual guide, please refer to the official installation video below.

Voor jy begin

• Measure your door's backset, cross bore, and thickness to ensure compatibility.
• Gather all required tools: Phillips head screwdriver, 4 AA batteries (included), and potentially a hammer and wood block for drive-in latches.

Installasie stappe

1. Pas die rugstel aan: Extend the bolt by rotating the D-shaped crank. Hold the latch in front of the door hole. If the D-shaped crank is centered, no adjustment is needed. If not, twist the latch to the larger setting.
2. Installeer die Latch and Strike: Ensure the 'UP' marking on the latch faces upward. Install the latch on the door with the provided short wood screws. If using a drive-in latch, use a hammer and wood block to tap it into position. Re-extend the latch bolt. Attach the strike plate to the door frame using the two long screws closest to the door jamb and two short screws.
3. Berei die eksterne sleutelbord voor: If your door's bore hole diameter is 2-1/8 inches, attach the provided adapter ring to the keypad. For 1-1/2 inch bore holes, the adapter ring is not needed.
4. Installeer die buite-montering en monteringsplaat: Route the cable underneath the latch. Insert the torque blade through the latch, aligning its D-shape with the crank. Firmly position the exterior assembly onto the door. Thread the cable and torque blade through the center hole of the mounting plate and position it flush against the door. Slide the cable into the small notch at the bottom. Secure the mounting plate to the door and exterior assembly with the mounting bolts. Let op: moenie te styf trek nie. Insert the key and test the latch for smooth operation. Adjust mounting screws if necessary. Remove the key and ensure the latch bolt is extended.
5. Disassemble the Interior Assembly: Ensure the turn piece is in the vertical position and remove the cover. Verify the turn piece shaft is oriented as shown in the video. Remove and set aside the battery pack for later installation.
6. Installeer die binne-samestelling: Align the white arrows on the two cable connectors and firmly push them together. Ensure cables are clear of pinching and route excess cable flat across the bottom of the interior housing. Align the torque blade with the turn piece shaft and push the interior assembly flush against the door. Insert and tighten the small screws to secure the interior assembly onto the mounting plate.
7. Install the Batteries and Perform the Door Handing Process: Load 4 AA batteries into the battery pack, ensuring correct polarity. With the door open, insert the battery pack into the interior assembly. The SmartCode mechanism will automatically drive the bolt in and out several times to determine proper handing. This step is crucial for proper operation.
8. Voer die Insluitingsproses (Z-Wave) uit: Initiate the inclusion process at your smart home controller. When prompted, press button 'A' on the lock one time to include it in your system. Refer to your controller's instructions for more information.
9. Install the Interior Cover: Install the interior cover over the interior assembly with three screws. The window on the interior cover is locked by default to prevent tampering. If desired, you may remove the security screw from the window so it can slide up for quick access to batteries and buttons while the cover is installed.

Bedryfsinstruksies

Figuur 2: Buitekant view of the Kwikset SmartCode 888 on a door.

Sleutellose toegang

Enter your personalized 4-8 digit user code on the backlit keypad to unlock the door. To lock the door, simply press the 'Lock' button.

Smart Home Integration (Z-Wave Plus)

With a compatible smart home system (e.g., Amazon Alexa, SmartThings, Vera), you can remotely lock or unlock your door from anywhere using your smartphone. You can also receive notifications when someone locks or unlocks your door, or check the door lock status.

Outo-sluitfunksie

The lock can be configured to automatically lock after a set period, providing added security and peace of mind. Refer to your smart home system's settings or the detailed instruction sheet for programming this feature.

Onderhoud

Battery vervanging

The SmartCode 888 operates on 4 AA batteries. When the batteries are low, the lock will provide an indicator. To replace, slide up the interior cover (if the security screw was removed) or remove the cover, then replace the battery pack. Ensure correct polarity. After replacing, the lock may perform a door handing process again.

SmartKey-sleutel weer

The lock features SmartKey Security re-key technology, allowing you to re-key the lock yourself in seconds to match an existing Kwikset key. This is useful if you have recently moved or wish to use fewer keys for multiple locks.

Figure 3: SmartKey Security re-keying process. Insert your current key, turn 90 degrees, insert the SmartKey tool, remove the old key, insert the new key, and turn 180 degrees back.

Probleemoplossing

• Latch not operating smoothly: If the latch does not operate smoothly after installation, adjust the mounting screws on the interior assembly. Ensure the torque blade is correctly aligned with the latch crank.
• Z-Wave network connection issues: If the lock loses network connection, ensure your Z-Wave hub is within range and consider using Z-Wave repeaters if necessary. Re-initiate the inclusion process if the connection is lost.
• Slot reageer nie: Check the battery level. Replace all four AA batteries if they are low or depleted. Ensure batteries are inserted with correct polarity.
• Sleutelbord lig nie op nie: This model features a backlit keypad. If it's not lighting up, check battery levels.

Spesifikasies

Waarborg en Ondersteuning

Waarborg inligting

The Kwikset SmartCode 888 comes with a Lewenslange meganiese en afwerkingswaarborg en a 1-jaar elektroniese waarborgBewaar asseblief u bewys van aankoop vir waarborgeise.

Kliënte ondersteuning

For further assistance, technical support, or to order replacement parts, please visit the official Kwikset website or contact their customer service department. Detailed contact information can typically be found on the Kwikset packaging or their official webwebwerf.