GoControl WS15Z5-1 Z-Wave(R) Wall Switch User Manual

Inleiding

Thank you for choosing the GoControl WS15Z5-1 Z-Wave Wall Switch. This smart switch allows you to control your lighting or other connected loads remotely via a Z-Wave network, as well as manually. It integrates seamlessly into your smart home system, providing convenience and energy efficiency. Please read this manual carefully before installation and operation to ensure proper use and safety.

Veiligheidsinligting

WAARSKUWING: Risk of Electric Shock. Installation should be performed by a qualified electrician. Disconnect power at the circuit breaker or fuse box before installation or servicing. Use only copper wire for connections. Do not exceed the maximum load ratings.

• Maak seker dat die krag by die stroombreker AF is voor installasie.
• Hierdie toestel is bedoel vir installasie in ooreenstemming met die Nasionale Elektriese Kode en plaaslike regulasies.
• Do not use in wet locations or where directly exposed to water.
• Slegs vir binnenshuise gebruik.

Pakketinhoud

• GoControl WS15Z5-1 Z-Wave Wall Switch
• Installasie skroewe
• Wire Nuts (may vary by package)
• Gebruikershandleiding (hierdie dokument)

Opstelling en installasie

Follow these steps carefully to install your GoControl Z-Wave Wall Switch.

1. Wiring the Switch

1. Skakel krag af: Locate the circuit breaker controlling the switch you are replacing and turn it OFF. Verify power is off by attempting to turn on the light or appliance.
2. Verwyder ou skakelaar: Carefully remove the existing wall plate and switch from the wall box. Disconnect the wires from the old switch, noting which wire was connected to which terminal (Line, Load, Neutral, Ground).
3. Identifiseer Drade:
   • Lyn (Warm): Usually black, coming from the circuit breaker.
   • Laai: Usually black, going to the light fixture or appliance.
   • Neutraal: Usually white, often bundled together in the back of the box. (Required for Z-Wave switches).
   • Grond: Usually green or bare copper.
4. Koppel Nuwe Skakelaar: Connect the wires to the GoControl WS15Z5-1 switch terminals as follows:
   • Koppel die Lyn wire to the terminal marked "LINE".
   • Koppel die Laai wire to the terminal marked "LOAD".
   • Koppel die Neutraal wire to the terminal marked "NEUTRAL".
   • Koppel die Grond wire to the terminal marked "GROUND".

   Ensure all connections are secure. If you are unsure about wiring, consult a qualified electrician.

5. Monteer skakelaar: Carefully push the wired switch into the wall box. Secure it with the provided screws.
6. Installeer muurplaat: Attach the new or existing wall plate.
7. Herstel krag: Skakel die krag weer AAN by die stroombreker.

Figuur 1: Voorkant view of the GoControl WS15Z5-1 Z-Wave Wall Switch.

2. Z-Wave Inclusion (Pairing)

To integrate the switch into your Z-Wave network, you need to "include" it with your Z-Wave controller.

1. Put your Z-Wave controller into Inclusion/Pairing mode. (Refer to your Z-Wave controller's manual for specific instructions).
2. On the GoControl WS15Z5-1 switch, quickly press the top or bottom paddle een keer. The LED indicator on the switch will blink to confirm inclusion mode.
3. The controller will confirm successful inclusion. The switch's LED will stop blinking and remain solid or turn off, depending on its status.
4. If inclusion fails, refer to the Troubleshooting section or try "Exclusion" first.

Figure 2: The Z-Wave logo, indicating compatibility with Z-Wave networks.

Bedien die skakelaar

Handmatige beheer

• Druk die bo of the paddle to turn the connected load ON.
• Druk die onderkant of the paddle to turn the connected load AF.

Z-Wave beheer

Once included in your Z-Wave network, you can control the switch remotely using your Z-Wave controller, hub, or compatible smart home application.

• Use your Z-Wave app or controller interface to toggle the switch ON/OFF.
• The switch supports standard Z-Wave commands for basic on/off functionality.

Figure 3: GoControl products integrate with smart home systems for control via smartphones and other devices.

Figure 4: Diagram illustrating GoControl's integration across various smart home categories like Climate, Lighting, Security, Sensors, and Access.

Onderhoud

The GoControl WS15Z5-1 Z-Wave Wall Switch requires minimal maintenance.

• Skoonmaak: Om die skakelaar skoon te maak, vee dit af met 'n sagte, damp lap. Moenie skuur skoonmaakmiddels of oplosmiddels gebruik nie.
• Firmware -opdaterings: Check the GoControl website or your Z-Wave controller's documentation for information on potential firmware updates.
• Algemene sorg: Maak seker dat die skakelaar nie aan oormatige vog of uiterste temperature blootgestel word nie.

Probleemoplossing

Z-Wave Exclusion (Removing from Network)

If you need to remove the switch from your Z-Wave network, follow these steps:

1. Put your Z-Wave controller into Exclusion mode. (Refer to your Z-Wave controller's manual for specific instructions).
2. On the GoControl WS15Z5-1 switch, quickly press the top or bottom paddle een keer. The LED indicator will blink to confirm exclusion mode.
3. The controller will confirm successful exclusion. The switch's LED will stop blinking.

Spesifikasies

Waarborg en Ondersteuning

GoControl products are designed for reliability and performance. For warranty information, technical support, or further assistance, please visit the official GoControl webwebwerf of kontak hul kliëntediensafdeling.

Webwebwerf: www.gocontrol.com

Vervaardiger: GOCONTROL