TOPGREENER TSOS5-W In-Wall PIR Motion Sensor Light Switch User Manual

1. Inleiding

The TOPGREENER TSOS5-W is an in-wall Passive Infrared (PIR) motion sensor light switch designed to automatically control lighting, fans, and motors based on occupancy detection. This single-pole switch requires a neutral wire for proper operation and offers AUTO, ON, and OFF modes for flexible control. It is suitable for various indoor applications, providing convenience and energy savings.

2. Belangrike veiligheidsinligting

WAARSKUWING: To avoid fire, shock, or death, turn off power at the circuit breaker or fuse and test that the power is off before wiring. Installation should be performed by a qualified electrician or a person with electrical knowledge.

This device requires a neutral wire for installation. Verify the presence of a neutral wire in your electrical box before proceeding.
For single-pole use only. Do not use in 3-way or multi-way switch configurations.
Do not exceed the maximum load ratings: CFL/LED: 150W; Incandescent/Halogen: 500W; Motor: 1/8 HP; Fluorescent 500VA.
Maak seker dat alle draadverbindings stewig en behoorlik geïsoleer is.
Slegs binnenshuise gebruik.

3. Pakketinhoud

TOPGREENER TSOS5-W Motion Sensor Switch
Draadmoere
Instruksie Handleiding

Note: Wall plate sold separately.

4. Produkspesifikasies

Modelnommer	TSOS5-W
Voltage	120VAC
Tipe laai	CFL/LED: 150W; Incandescent/Halogen: 500W; Motor: 1/8 HP; Fluorescent 500VA
Soort sensor	PIR (passiewe infrarooi)
Veld van View	180 grade
Dekkingsgebied	Tot 980 vk
Tydsvertraging	Adjustable: 15 sec (test mode), 10 min, 20 min, 30 min
Sensitiwiteit	Adjustable: 30% to 100%
Bedradingvereiste	Neutrale draad benodig
Afmetings	5.1 x 3 x 2.2 duim
Gewig	4.97 onse (0.14 kilogram)
Montage tipe	Embedded (In-Wall)

5. Installasie-instruksies

Voordat jy begin: Ensure power is OFF at the circuit breaker. This device requires a neutral wire. If you are unsure about your wiring, consult a qualified electrician.

5.1 Bedradingsdiagram

The TSOS5-W switch has four wires for connection: Line (Hot), Load, Neutral, and Ground.

Swart draad: Connects to the Line (Hot) wire from the electrical box.
Rooi draad: Connects to the Load wire (to the light fixture/fan).
Wit draad: Connects to the Neutral wire from the electrical box.
Groen draad: Connects to the Ground wire from the electrical box.

Figuur 1: Voorkant view of the TOPGREENER TSOS5-W motion sensor switch, showing the sensor lens and the OFF-AUTO-ON slider.

Diagram showing the internal components of the motion sensor switch, highlighting the PIR sensor, customizable controls, daylight detection, fault tolerance, and fire-resistant materials.

Figure 2: Internal components of the TSOS5-W, illustrating the PIR sensor, customizable controls, and safety features.

5.2 Stap-vir-stap installasie

Skakel krag af: Locate the circuit breaker that controls the power to the switch box and turn it OFF. Verify power is off using a voltage toetser.
Verwyder ou skakelaar: Verwyder die bestaande muurplaat en skakelaar versigtig van die elektriese boks. Ontkoppel die drade van die ou skakelaar.
Identifiseer Drade: Identify the Line (Hot), Load, Neutral, and Ground wires in your electrical box. The neutral wire is typically white. If you are unsure, consult a qualified electrician.
Koppel drade: Using the provided wire nuts, connect the wires from the TSOS5-W switch to the corresponding wires in the electrical box:
- Black switch wire to Line (Hot) wire.
- Red switch wire to Load wire.
- White switch wire to Neutral wire.
- Green switch wire to Ground wire.
Monteer skakelaar: Carefully fold the wires into the electrical box and secure the TSOS5-W switch to the box using the mounting screws.
Installeer muurplaat: Heg die muurplaat (apart verkoop) oor die skakelaar vas.
Herstel krag: Skakel die krag weer AAN by die stroombreker.

6. Operasie

The TSOS5-W features a slider switch for mode selection and adjustable dials for sensitivity and time delay, located behind the faceplate.

6.1 Moduskeuse

Close-up of the TSOS5-W switch showing the OFF, AUTO, and ON positions of the slider switch.

Figure 3: The OFF-AUTO-ON slider switch for mode selection.

AUTO Mode (Occupancy Sensor): In this mode, the switch automatically turns lights ON when motion is detected and OFF after a set time delay when no motion is detected. This is the primary energy-saving mode.
AAN-modus: This mode overrides the sensor, keeping the lights ON continuously, similar to a standard light switch.
AF -modus: This mode overrides the sensor, keeping the lights OFF continuously, similar to a standard light switch.

6.2 Adjusting Settings (Behind Faceplate)

To access the adjustment dials, carefully remove the faceplate of the switch. You will find dials for Time Delay and Sensitivity.

Tydsvertraging: This setting determines how long the lights remain ON after the last detected motion. Adjustable options include 15 seconds (test mode), 10 minutes, 20 minutes, and 30 minutes. Rotate the dial to select the desired delay.
Sensitiwiteit: This setting controls the sensor's responsiveness to motion. It can be adjusted from 30% to 100%. A higher sensitivity setting will detect smaller movements or movements at a greater distance. Rotate the dial to adjust.

Image showing the TSOS5-W switch installed in a laundry room, with a woman carrying a laundry basket. The text 'Hands-Free Occupancy modes auto ON/OFF' is overlaid.

Figure 4: The TSOS5-W in an occupancy sensing application, providing hands-free lighting control.

7. Probleemoplossing

Probleem	Moontlike oorsaak/oplossing
Lights do not turn ON/OFF or device does not work after installation.	Verify power is ON at the circuit breaker. Ensure all wiring connections (Line, Load, Neutral, Ground) are correct and secure. A neutral wire is required. Check if the switch is in the correct mode (AUTO, ON, OFF). Confirm the load (light/fan) is functioning correctly. As die probleem voortduur, kontak kliëntediens.
Lights turn ON unexpectedly or stay ON too long.	Adjust the sensitivity dial to a lower setting. Check for heat sources or air currents (e.g., HVAC vents, windows) within the sensor's field of view that might be causing false triggers. Reduce the time delay setting.
Lights do not turn ON when motion is detected.	Ensure the switch is in AUTO mode. Increase the sensitivity setting. Verify the sensor's field of view belemmer word nie. Check if the ambient light level is too high (some sensors have a daylight detection feature that prevents lights from turning on if sufficient natural light is present).
Cannot set time delay less than 10 minutes.	The specified time delay options are 15 seconds (test mode), 10 minutes, 20 minutes, and 30 minutes. Intermediate settings between 15 seconds and 10 minutes are not available.

8. Onderhoud

Clean the sensor lens periodically with a soft, dry cloth to ensure optimal performance. Avoid using abrasive cleaners.
Do not paint over the sensor lens.
No user-serviceable parts inside. Do not attempt to disassemble the unit.

9. Waarborg en Ondersteuning

TOPGREENER products are designed for reliability and performance. For warranty information or technical support, please contact TOPGREENER customer service. Refer to the product packaging or the official TOPGREENER webwebwerf vir kontakbesonderhede.

Vervaardiger: Top Greener Inc