Braeburn 5-2 Day Programmable Thermostat

Inleiding

This manual provides comprehensive instructions for the installation, operation, programming, and maintenance of your Braeburn 5-2 Day Programmable Thermostat. Please read this manual thoroughly before attempting to install or operate your new thermostat.

Figuur 1: Voorkant view of the Braeburn 5-2 Day Programmable Thermostat, showing the large blue backlit display, system mode switch, fan mode switch, and programming buttons.

Kenmerke

• 5-2 Day Programmability
• Groot 2 vk. In. Vertoon met helderblou agtergrondlig
• Verstelbare temperatuurlimiete
• Hardwire or Battery Powered (24V AC)
• Permanente geheue behou instellings
• Filter Check Monitor
• Verstelbare temperatuur differensiaal
• Adaptive Recovery Mode (ARM)
• ESD Guard Electronic Circuitry
• Kompressor kort siklus beskerming
• Tydelike programverwydering
• Programmeerbare verlengde houmodus
• Voortoegang-terugstelknoppie
• F° / C° Skakelaar

Installasie en opstelling

Veiligheidsmaatreëls

• WAARSKUWING: Disconnect power to the heating and cooling system before installing or servicing the thermostat.
• Installasie moet deur 'n gekwalifiseerde tegnikus uitgevoer word.
• Maak seker dat die bedrading aan plaaslike elektriese kodes voldoen.

Monteerplek

Install the thermostat on an inside wall, approximately 5 feet (1.5m) above the floor. Avoid locations near heat sources (lamps, sunlight, fireplaces), drafts (windows, doors), or unconditioned spaces (unheated hallways, outside walls).

Bedradingsinstruksies

This thermostat is designed for single-stage (1 Heat/1 Cool) systems. It can be powered by 24V AC hardwire or batteries.

Typical Terminations: Rc, Rh, O, B, Y1, W1, G, C

1. Turn off power to the HVAC system at the circuit breaker.
2. Remove the old thermostat from the wall plate.
3. Label each wire with the terminal designation from your old thermostat.
4. Mount the new thermostat base plate to the wall.
5. Connect the labeled wires to the corresponding terminals on the new thermostat. Refer to the wiring diagram provided with your thermostat for specific connections.
6. Insert 2 AA alkaline batteries (not included) into the battery compartment if using battery power or as a backup.
7. Attach the thermostat body to the base plate.
8. Herstel krag aan die HVAC -stelsel.

Gebruik jou termostaat

Stelselmodusskakelaar

Located on the front of the thermostat, this switch controls the overall operation mode:

• KOEL: Die termostaat sal jou verkoelingstelsel bedryf.
• AF: The heating and cooling systems are turned off.
• HITTE: Die termostaat sal jou verhittingstelsel bedryf.

Fan Mode Switch

Located on the front of the thermostat, this switch controls the fan operation:

• VOERTUIG: The fan runs only when the heating or cooling system is active.
• OP: The fan runs continuously, regardless of heating or cooling calls.

Stel temperatuur

Gebruik die UP en AF arrow buttons on the right side of the display to adjust the desired temperature (setpoint). The display will show both the current room temperature and the setpoint.

Programming (5-2 Day)

The 5-2 day programming allows you to set different schedules for weekdays (Monday-Friday) and weekends (Saturday-Sunday). Each day can have up to 4 program periods: Morning, Day, Evening, and Night.

Stel tyd en dag in

1. Druk die PROG button once. The display will show the current time flashing.
2. Gebruik die UP or AF pyltjies om die tyd aan te pas.
3. Druk PROG again to advance to the day setting. The day will flash.
4. Gebruik die UP or AF arrows to adjust the day.
5. Druk PROG or wait 15 seconds to exit.

Setting Program Schedule

1. Druk die PROG button until "MON-FRI" appears and the time for the first period (Morning) flashes.
2. Gebruik die UP or AF arrows to set the desired time for the Morning period.
3. Druk PROG. The temperature for the Morning period will flash.
4. Gebruik die UP or AF pyltjies om die verlangde temperatuur in te stel.
5. Repeat steps 2-4 for the Day, Evening, and Night periods for "MON-FRI".
6. After setting the "MON-FRI" schedule, press PROG to advance to "SAT-SUN" and repeat the process for weekend programming.
7. Druk TERUGKEER or wait 15 seconds to exit programming mode.

Tydelike programverwydering

To temporarily change the temperature without affecting the program, simply use the UP or AF arrows. The thermostat will hold this temperature until the next program period begins.

Permanente Hou

Druk die HOU button. The thermostat will maintain the current temperature indefinitely. To cancel, press HOU weer of druk PROG to resume the schedule.

Onderhoud

Battery vervanging

When the battery indicator appears on the display, replace the 2 AA alkaline batteries immediately to ensure proper operation and prevent loss of settings. The thermostat has permanent memory, so settings will be retained during battery replacement.

1. Gently pull the thermostat body away from the wall plate.
2. Verwyder die ou batterye.
3. Insert new AA alkaline batteries, observing polarity (+/-).
4. Klik die termostaat se liggaam terug op die muurplaat.

Skoonmaak

Maak die termostaat skoon met 'n sagte, damp lap. Moenie skuur skoonmaakmiddels of oplosmiddels gebruik nie.

Filter Check Monitor

The thermostat may feature a filter check monitor that reminds you to change your air filter. Consult your HVAC system manual for recommended filter replacement intervals.

Probleemoplossing

If problems persist, contact a qualified HVAC technician or Braeburn customer support.

Spesifikasies

Waarborg en Ondersteuning

For warranty information and technical support, please refer to the documentation included with your product or visit the official Braeburn webwebwerf. Bewaar u aankoopbewys as bewys van aankoop.

Vervaardiger: Braeburn