SEM Products 15093 Light Buckskin Color Coat User Manual

Produk verbyview

SEM Color Coat is a specialized elastomeric coating designed to restore or change the color of most vinyl surfaces, flexible and rigid plastics, carpet, and velour. This product is not a dye; it is a fade-resistant, flexible, and permanent coating.

It is formulated to provide a durable finish that integrates with the material, offering a renewed appearance without cracking or peeling when properly applied.

Voorbereiding en Opstelling

Proper surface preparation is crucial for optimal adhesion and durability of SEM Color Coat. Follow these steps carefully:

Oppervlakte skoonmaak:

• For Vinyl: Use SEM Soap (Part No. 39362) followed by Vinyl Prep (Part No. 38343) or Zero VOC Surface Cleaner (Part No. 40404).
• For Plastic: Apply an appropriate adhesion promoter. Do not use more than one product on the same job. Recommended products include Plastic Adhesion Promoter (Part No. 38363) or XXX Adhesion Promoter (Part No. 7723).

Ensure the surface is clean, dry, and free of any contaminants like grease, oil, or silicone before application.

Gebruiksaanwysings (Toepassing)

Once the surface is prepared, proceed with the application of SEM Color Coat:

1. Skudblik: Shake the aerosol can thoroughly for at least one minute after the mixing ball begins to rattle. Continue shaking periodically during application.
2. Toepassingsafstand: Hold the can approximately 6-8 inches (15-20 cm) from the surface to be coated.
3. Apply Light Coats: Apply multiple light, even coats. Avoid applying heavy coats to prevent runs or uneven coverage.
4. Drying Time Between Coats: Allow 5-10 minutes of drying time between each coat. Apply additional coats until the desired hiding and color depth are achieved.

For detailed information, refer to the RAP-1 or Technical Data Sheet available from SEM Products.

Onderhoud

Once applied and fully cured, SEM Color Coat is a durable and fade-resistant finish. To maintain its appearance, clean the coated surface with mild soap and water. Avoid harsh abrasives or strong chemical cleaners, as these may damage the coating.

Probleemoplossing

Most application issues can be prevented by following the preparation and application instructions carefully. If issues arise:

• Swak adhesie: Often caused by inadequate surface cleaning or improper use of adhesion promoter. Ensure surfaces are thoroughly cleaned and prepped as per instructions.
• Uneven Finish/Runs: Typically results from applying coats too heavily or not allowing sufficient drying time between coats. Apply lighter, multiple coats.
• Kleurwanpassing: Ensure the correct product color was selected for the intended application.

For persistent issues, consult the SEM Products technical data sheet or contact customer support.

Spesifikasies

Veiligheidsinligting

DANGER: EXTREMELY FLAMMABLE AEROSOL. PRESSURIZED CONTAINER. MAY BURST IF HEATED. HARMFUL OR FATAL IF SWALLOWED. VAPOUR HARMFUL. CAUSES SERIOUS EYE IRRITATION. CAUSES SKIN IRRITATION.

Read all cautions on the back panel and product safety data sheet before use.

Algemene voorsorgmaatreëls:

• Hou weg van hitte, vonke, oop vlamme en warm oppervlaktes. Moenie rook nie.
• Houer onder druk: Moet nie deurboor of verbrand nie, selfs na gebruik.
• Wear protective gloves, protective clothing, eye protection, and face protection.
• Was deeglik na hantering.
• Store locked up. Keep cool. Protect from sunlight. Do not expose to temperatures exceeding 50°C (122°F).
• Gooi inhoud/houer weg in ooreenstemming met plaaslike, streeks-, nasionale en internasionale regulasies.

Noodhulp:

• INDIEN IN DIE OË: Spoel versigtig met water vir 'n paar minute. Verwyder kontaklense, indien teenwoordig en maklik om te doen. Gaan voort met spoel.
• INDEMING: Supply fresh air. Consult a doctor if case of complaints.
• INDIEN OP DIE VEL: Wash with water and soap and rinse thoroughly.
• INDIEN INGESLUK: Do NOT induce vomiting. Consult a doctor immediately.

WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects.

For more detailed information, refer to the Safety Data Sheet (SDS) for this product.

Ondersteuningsinligting

For further assistance, technical data sheets, or product inquiries, please contact SEM Products, Inc.:

SEM PRODUCTS, INC.
Rock Hill, SC 29730
Foon: 800-831-1122

Besoek die amptenaar website for more information on Color Coat aerosols: www.semproducts.com/color-coat-aerosols/