1. Inleiding
The Mitutoyo VDS-15DCX is a high-precision digital depth gauge designed for accurate measurement of depths, steps, and grooves. This manual provides essential information for the safe and effective use, maintenance, and troubleshooting of your instrument. Please read this manual thoroughly before operating the device.
Image: Mitutoyo VDS-15DCX Digital Depth Gauge. This image displays the main unit of the digital depth gauge, showing its digital display, measuring base, and measuring rod.
2. Opstelling
2.1 Uitpak en inspeksie
- Carefully remove the depth gauge from its packaging.
- Inspect the instrument for any signs of damage that may have occurred during transit. If damage is found, do not use the device and contact your supplier.
- Verifieer dat al die komponente wat in die paklys gelys word, teenwoordig is.
2.2 Battery installasie
The VDS-15DCX uses one SR44 silver oxide button cell battery.
- Locate the battery cover on the back of the digital display unit.
- Using a small screwdriver or coin, gently turn the battery cover counter-clockwise to open.
- Insert a new SR44 battery with the positive (+) side facing upwards.
- Replace the battery cover and turn clockwise to secure.
- Press the ON/OFF button to confirm the display powers on.
2.3 Cleaning Measuring Surfaces
Before use, gently wipe the measuring base and the tip of the measuring rod with a clean, lint-free cloth. Ensure no dust, oil, or debris is present on these surfaces, as this can affect measurement accuracy.
2.4 Zero-Setting Procedure
To ensure accurate measurements, the depth gauge must be zero-set before use.
- Place the depth gauge on a flat, stable, and clean reference surface.
- Ensure the measuring base is flush with the reference surface and the measuring rod is fully retracted.
- Druk die NUL button. The display should show '0.00' or '0.000'.
- The instrument is now ready for measurement.
3. Bedryfsinstruksies
3.1 Basiese Meting
- Ensure the depth gauge is properly zero-set (refer to Section 2.4).
- Place the measuring base firmly on the top surface of the workpiece or feature to be measured.
- Slowly extend the measuring rod until its tip makes contact with the bottom surface of the depth or step. Ensure the rod is perpendicular to the bottom surface.
- Lees die meetwaarde wat op die LCD-skerm vertoon word.
3.2 Eenheidsomskakeling (mm/duim)
To switch between metric (mm) and imperial (inch) units, press the mm/duim button. The display will show the current unit of measurement.
3.3 Absolute (ABS) and Incremental (INC) Measurement
The VDS-15DCX allows for both absolute and incremental measurements.
- Absolute (ABS) Mode: This mode measures from the true zero point, which is set when the gauge is zeroed on a reference surface.
- Incremental (INC) Mode: To measure a difference from an arbitrary point, position the measuring rod at the desired reference point on the workpiece and press the NUL button. The display will reset to zero, and subsequent movements will show the incremental distance from this new zero point. Press the ABS/INC button to toggle between modes.
3.4 Data Vashou Funksie
If your model includes a HOU button, pressing it will freeze the current reading on the display, allowing you to remove the gauge from the workpiece and record the measurement. Press the button again to release the hold function.
4. Onderhoud
4.1 Skoonmaak
- After each use, wipe the entire instrument, especially the measuring surfaces, with a clean, dry, lint-free cloth.
- For stubborn dirt or oil, use a cloth lightly dampened with isopropyl alcohol. Avoid using strong solvents or abrasive cleaners.
- Do not immerse the depth gauge in any liquid.
4.2 Berging
- Store the depth gauge in its original protective case when not in use.
- Store in a dry environment, away from direct sunlight, extreme temperatures, and high humidity.
- Avoid storing in areas with excessive dust or corrosive fumes.
4.3 Batteryvervanging
Replace the battery when the display becomes dim or an indicator (e.g., 'B' or battery icon) appears on the screen. Refer to Section 2.2 for battery installation instructions. Dispose of used batteries according to local regulations.
4.4 Kalibrasiekontroles
Periodically check the accuracy of the depth gauge using a known reference standard (e.g., gauge blocks). If the readings are consistently outside the specified accuracy, the instrument may require professional calibration or repair.
5. Probleemoplossing
| Probleem | Moontlike oorsaak | Oplossing |
|---|---|---|
| Vertoning skakel nie aan nie | Dooie of verkeerd geïnstalleerde battery | Replace battery (Section 2.2) or ensure correct polarity. |
| Onakkurate lesings |
|
|
| Display shows 'E' or error code | Internal error or sensor issue | Remove and reinsert battery. If error persists, contact customer support. |
| Knoppies reageer nie | Low battery or internal malfunction | Replace battery. If issue continues, contact customer support. |
6. Spesifikasies
| Kenmerk | Spesifikasie |
|---|---|
| Modelnommer | VDS-15DCX (571-201-20) |
| Meetreeks | 0-150 mm (0-6 duim) |
| Resolusie | 0.01 mm (0.0005 duim) |
| Akkuraatheid | ±0.02 mm (±0.001 duim) |
| Vertoon | LCD |
| Kragtoevoer | SR44 (1 pc) |
| Gewig | 207 g (0.45 lbs) |
| Vervaardiger | Mitutoyo |
7. Waarborginligting
Mitutoyo products are manufactured to high standards and are typically covered by a limited warranty against defects in materials and workmanship. The specific terms and duration of the warranty may vary by region and product. Please refer to the warranty card included with your product or contact your local Mitutoyo distributor for detailed warranty information.
8. Kliëntediens
For technical assistance, service, or inquiries regarding your Mitutoyo VDS-15DCX digital depth gauge, please contact your authorized Mitutoyo distributor or visit the official Mitutoyo website for regional contact information. When contacting support, please have your model number (VDS-15DCX) and serial number (if applicable) ready.