Produk verbyview
The SEM Color Coat is a specialized elastomeric coating designed to restore or change the color of various surfaces, including most vinyl, flexible and rigid plastics, carpet, and velour. This product is formulated as a fade-resistant, flexible, and permanent coating, not a dye.
Beeld: Voorkant view of the SEM Color Coat aerosol can, showing the product name, "Flexible Coating," and a graphic of a car interior.
Veiligheidsinligting
DANGER! EXTREMELY FLAMMABLE AEROSOL.
Causes skin irritation. Causes serious eye irritation. Harmful or fatal if swallowed. Vapor harmful. Read cautions on back panel.
- Hou weg van hitte/vonke/oop vlamme/warm oppervlaktes. Geen rook nie.
- Houer onder druk: Moet nie deurboor of verbrand nie, selfs na gebruik.
- Moet nie op 'n oop vlam of ander ontstekingsbron spuit nie.
- Protect from sunlight. Do not expose to temperatures exceeding 50°C/122°F.
- Gooi inhoud/houer weg in ooreenstemming met plaaslike/streeks/nasionale/internasionale regulasies.
- Vermy asemhaling van stof/rook/gas/mis/dampe/sproei.
- Was deeglik na hantering.
- Dra beskermende handskoene/oogbeskerming/gesigbeskerming.
- IF ON SKIN: Wash with plenty of water and soap. If skin irritation occurs, get medical advice/attention.
- IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists, get medical advice/attention.
- IF SWALLOWED: Immediately call a POISON CENTER/doctor. Do NOT induce vomiting.
- IF INHALED: Remove person to fresh air and keep comfortable for breathing. Call a POISON CENTER/doctor if you feel unwell.
Beeld: Agterkant view of the SEM Color Coat aerosol can, displaying safety warnings and product information.
Opstelling en voorbereiding
Proper preparation is crucial for optimal adhesion and longevity of the coating. Follow these steps carefully:
- Verwyder Onderdele: Disassemble and remove the parts you intend to paint from the vehicle or item.
- Deeglike skoonmaak: Thoroughly clean the surfaces with soap and a degreaser to remove all dirt, grease, and contaminants.
- Light Sanding (Optional but Recommended): For improved adhesion, lightly sand the surface with 800-grit sandpaper.
- Eindskoonmaak: Clean the surface thoroughly again with acetone. This step is very important for proper adhesion. Wear rubber gloves and safety goggles during this step as acetone can burn through gloves and is irritating to eyes.
- Temperatuur: Ensure the application temperature is approximately 21°C (70°F).
Beeld: Sykant view of the SEM Color Coat aerosol can, showing general application instructions and product details.
Gebruiksaanwysings (Toepassing)
Apply the SEM Color Coat in multiple thin layers, allowing adequate drying time between coats. Do not use a heat gun.
- First Coat (Light Dusting): Apply a very light dusting coat. Alternatively, apply an adhesion promoter if desired, which can help the paint adhere better to surfaces.
- Second Coat (Light Dusting): Apply another light dusting coat.
- Subsequent Coats (Coverage): Apply a third coat with more coverage, followed by a fourth and fifth coat for complete and even coverage.
- Droogtyd: Allow 10-15 minutes in between coats. The exact drying time may vary depending on the ambient temperature.
The product is designed to be fast-drying, with a dry time of approximately 1 hour.
Beeld: Bo view of the SEM Color Coat aerosol can, displaying the model number "15813" and color "Medium Dark Pewter" on the cap.
Onderhoud
Once applied and fully cured, SEM Color Coat provides a durable and flexible finish. To maintain the appearance and longevity of the coating:
- Clean coated surfaces with mild automotive interior cleaners.
- Avoid harsh abrasives or strong chemical solvents that could damage the finish.
- While the product is designed to be permanent and fade-resistant, prolonged exposure to extreme conditions may affect its lifespan.
Probleemoplossing
| Probleem | Moontlike oorsaak | Oplossing |
|---|---|---|
| Poor Adhesion / Chipping | Inadequate surface preparation (e.g., not cleaned thoroughly, no sanding). | Ensure surfaces are meticulously cleaned with degreaser and acetone. Consider light sanding. Apply an adhesion promoter. |
| Uneven Color / Streaks | Too thick coats, insufficient shaking of can, or inconsistent spray pattern. | Apply multiple thin, even coats. Shake can well before and during use. Maintain consistent distance from surface. |
| Kleur Mismatch | Incorrect color selection for the original surface. | Verify the correct color code for your application. Test on an inconspicuous area first. Note that "Medium Dark Pewter" may vary slightly depending on the original surface's specific shade. |
Spesifikasies
- Handelsmerk: SEM
- Model Naam: 15813
- Kleur: Medium Dark Pewter (Color Code: #665D56)
- Voltooi tipe: Metaal
- Itemvolume: 12 Fluid Ounces (12 oz / 340 g)
- Itemvorm: Aërosol
- Tipe verf: Specialty Elastomeric Coating
- Spesifieke gebruike: Vinyl surfaces, flexible and rigid plastics, carpet, velour
- Oppervlak-aanbeveling: Carpet (also suitable for vinyl, plastic, velour)
- Binne/buiteluggebruik: Binne, Buitelug
- Spesiale kenmerk: Vinnig droog
- Droogtyd: Ongeveer 1 uur
- Waterweerstandvlak: Nie waterbestand nie
- Item gewig: 1 pond
- Produk afmetings: 8.38 x 5.63 x 7.88 duim
- UPC: 646786158131
Bykomende hulpbronne
For more detailed technical data and information, refer to the official SEM Color Coat Technical Data Sheet or RAP-1.
A relevant link for additional information can be found here: SEM Color Coat Technical Data
Waarborg en Ondersteuning
Information regarding product warranty and direct support contacts is not available in this manual. Please refer to the product packaging or the manufacturer's official website for warranty details and customer support options.