Gebruikershandleiding

1. Inleiding

The B&K Precision 2190B is a 100 MHz, two-channel analog oscilloscope designed for a wide range of electronics applications, including product design, assembly line testing, repair and servicing, and electrical engineering education. This instrument provides precise measurement and visualization of electrical signals over time, making it an essential tool for waveform analysis.

Key features include a vertical sensitivity to 5mV per division (1mV per division with gain control), ALT triggering for simultaneous dual-channel display, a hold-off function to stabilize complex signals, and TV synchronization capabilities. The 6-inch CRT display with an 8x10 division grid ensures clear waveform visualization. This manual provides essential information for the proper setup, operation, and maintenance of your 2190B oscilloscope.

2. Wat is in die boks?

Upon unpacking your B&K Precision 2190B oscilloscope, please verify that all the following items are included:

• 2190B analog oscilloscope unit
• Two (2) voltage probes
• Krag koord
• Gebruikershandleiding (hierdie dokument)
• Spaar lont

If any items are missing or damaged, please contact B&K Precision customer support immediately.

3. Produk verbyview

The B&K Precision 2190B oscilloscope is designed for intuitive operation and reliable performance. Below is an image of the unit, highlighting its general appearance and controls.

Figuur 3.1: Voorkant view of the B&K Precision 2190B Dual Trace Analog Oscilloscope. The image displays the main unit with its CRT screen on the left and various control knobs and input jacks on the right, including vertical and horizontal controls, trigger settings, and input channels.

Sleutel kenmerke:

• 100MHz bandwydte: Capable of accurately displaying signals up to 100 MHz.
• Twee kanale: Allows for simultaneous display and comparison of two independent signals.
• Vertikale Sensitiwiteit: Adjustable from 5mV/div to 1mV/div (with gain control) for capturing low-level signals.
• Stygtyd: 3.5 ns
• Sweep Tyd: 0.05µs/div to 0.5s/div
• Snellermodusse: AUTO, NORM, TV-V, TV-H
• Snellerbron: CH1, CH2, ALT, LINE, EXT
• 6" CRT Display: Clear, variable-illumination cathode ray tube display with an 8x10 division internal grid.

4. Opstelling

1. Plasing: Place the oscilloscope on a stable, level surface with adequate ventilation. Ensure there is sufficient space around the unit for air circulation. Avoid direct sunlight, excessive dust, high humidity, or strong vibrations.
2. Kragverbinding: Connect the provided power cord to the AC inlet on the rear panel of the oscilloscope and then to a grounded AC power outlet. Verify that the power supply voltage matches the rating specified on the oscilloscope's rear panel (100/120/220/240 V AC +/-10%, 50/60Hz).
3. Sondeverbinding: Connect the oscilloscope probes to the BNC input connectors (CH1 and CH2) on the front panel. Ensure the probe's ground clip is securely connected to the circuit's ground point.
4. Sondekompensasie: Before taking measurements, compensate the probes to ensure accurate waveform display. Connect the probe to a channel input and its tip to the probe compensation output (usually a square wave signal). Adjust the compensation trimmer on the probe until a flat-top square wave is displayed on the screen.

5. Bedryfsinstruksies

5.1 Basiese werking

• Krag aan: Press the power switch to turn on the oscilloscope. Allow a few moments for the CRT to warm up and display a trace.
• Intensity and Focus: Pas die INTENSITEIT en FOKUS knobs to achieve a clear, sharp trace.
• Posisionering: Gebruik die VERTIKALE POSISIE (for each channel) and HORISONTALE POSISIE knobs to move the trace to the desired position on the screen.
• Vertical Sensitivity (VOLTS/DIV): Kies die toepaslike VOLTS/DIV setting for the input signal. This determines the vertical scale of the waveform.
• Time Base (TIME/DIV): Kies die toepaslike TYD/DIV setting. This determines the horizontal scale (time per division) of the waveform.

5.2 Sneller

Triggering is crucial for obtaining a stable waveform display. The trigger circuit synchronizes the horizontal sweep with a specific point on the input signal.

• Snellerbron: Select the trigger source (CH1, CH2, ALT, LINE, EXT). For most applications, CH1 or CH2 is used.
• Snellermodus: Choose between AUTO, NORM, or TV modes. AUTO provides a trace even without a trigger signal. NORM requires a trigger signal to display a trace. TV modes are for video signals.
• Snellervlak: Pas die TRIGGER LEVEL knob to set the voltage point on the waveform where the sweep will begin.
• Helling: Select the trigger slope (positive or negative) to trigger on the rising or falling edge of the signal.

5.3 Dual Channel Operation (ALT Triggering)

Om view both CH1 and CH2 signals simultaneously, ensure both channels are enabled and select the ALT trigger source. This mode rapidly alternates between displaying CH1 and CH2, creating the appearance of a simultaneous display.

5.4 Delayed Sweep

The delayed sweep function allows for detailed examination of a specific portion of a waveform. Engage the delayed sweep mode and use the delay time control to position the magnified section. The sweep speed can be magnified by 10 times for enhanced resolution.

6. Onderhoud

Proper maintenance ensures the longevity and accuracy of your oscilloscope.

• Skoonmaak: Regularly clean the exterior of the oscilloscope with a soft, damp cloth. Do not use abrasive cleaners or solvents. Ensure the unit is powered off and unplugged before cleaning.
• Ventilasie: Hou die ventilasie-openinge vry van stof en obstruksies om oorverhitting te voorkom.
• Sondeversorging: Handle probes carefully. Avoid bending or kinking the cables. Store them properly to prevent damage to the tips and connectors.
• Sekering vervanging: If the oscilloscope does not power on, check the fuse located near the AC inlet. Replace it only with a fuse of the same type and rating as specified in the specifications or on the unit itself. Always unplug the power cord before replacing the fuse.
• Kalibrasie: For continued accuracy, periodic calibration by qualified service personnel is recommended.

7. Probleemoplossing

Hierdie afdeling bied oplossings vir algemene probleme wat u mag teëkom.

If the problem persists after attempting these solutions, please contact B&K Precision customer support.

8. Spesifikasies

Detailed technical specifications for the B&K Precision 2190B Dual Trace Analog Oscilloscope:

• Bandwydte: 100 MHz
• Kanale: Two (Dual Trace)
• Vertoon: 6-inch CRT, 8 x 10 division grid (1cm per division)
• Vertikale Sensitiwiteit: 5mV/div to 5V/div (to 1mV/div with gain control)
• Stygtyd: 3.5 ns
• Sweep Tyd: 0.05µs/div to 0.5s/div
• Snellermodusse: AUTO, NORM, TV-V, TV-H
• Snellerbron: CH1, CH2, ALT, LINE, EXT
• Kragvereistes: 100/120/220/240 V AC +/-10%, 50/60Hz, approximately 55W
• Afmetings (H x B x D): 324 x 398 x 132 mm (12.76 x 15.68 x 5.2 duim)
• Gewig: 8.5 kg (18.7 lb)
• Sertifiserings: Underwriters Laboratories (UL) certified

9. Waarborg en Ondersteuning

B&K Precision products are manufactured to high quality standards and are backed by a limited warranty. For specific warranty terms and conditions, please refer to the warranty card included with your product or visit the official B&K Precision webwebwerf.

For technical support, service, or inquiries regarding your 2190B oscilloscope, please contact B&K Precision customer service. Contact information can typically be found on the company's official webwebwerf of in die produkverpakking.

B&K Precision Headquarters: Yorba Linda, CA, USA